IC Do not exceed the screw-in torque of 3.5 Nm when installing piping. Exceeding this value may cause malfunctioning of the sensor. 4. The minimum bending radius of the cable is 50 mm. 5. Do not use pressure sensors with corrosive and/or inflammable gases or liquids. 1. Incorrect wiring can damage the switch and cause a malfunction or erroneous switch output.
Do not use with pressure or temperature beyond the specification range.
;(E a Slip exceeding retaining force may damage brake shoe, which could lead to reduced relaining force, resulting in its shorter lile a Cylinder loading should be within 35'/" of holding force when the brake is used for droo oroteclion, a Do not apply any impact when you load the cylinder in the locked position.
Caution Mounting 1) Do not subject the gauge to shocks, such as dropping during transportation and mounting, as this can cause loss of indication accuracy. 2) Do not use this gauge in a location with high temperature and humidity, as this may cause faulty operation. 3) When mounting the pressure gauge, be certain to use a wrench on the square wrench flats to screw it into place.
Do not use in locations having an explosive atmosphere. 2. When vibration or impact is applied, make sure to test in the 2.
Do not supply lubrication, as this is a non-lube product. The interior of the cylinder is lubricated at the factory, and lubrication with turbine oil, etc., will not satisfy the product's specifications. 6. Never reapply lubricant. Never reapply lubricant, as there may be a degradation of particulate generation or operation characteristics. 2.
For AC specifications, Nil is only set for electrical entry DO. Right Left Right Left IN IN Options (For details, refer to page 12.)
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.
Do not load the Card Motor with continuous or higher thrust than allowed for a prolonged time. When a pushing operation step data is selected, the pushing force is continuously generated from [Operation Start] until [Operation End (Stop)] is pressed.
Please avoid excessive overwriting. (4) Do not cut the power while data is being saved.
Use under conditions where pressure fluctuations (pulsations) exceeding 0.1 MPa do not occur. Operating pressure MAX. 0.99MPa Vacuum 1.310-6kPa Operating temperature 5oC to 80oC Element proof differential pressure MAX. 0.1MPa Element reverse differential pressure MAX. 0.05MPa Not possible to use with connecting in reverse.
Use under conditions where pressure fluctuations (pulsations) exceeding 0.1 MPa do not occur. Operating pressure MAX. 0.99MPa Vacuum 1.310-6kPa Operating temperature 5oC to 80oC SFB10MAX. 0.5MPa Element proof differential pressure SFB20-02 MAX. 1.0MPa SFB10MAX. 0.07MPa Not possible to use with connecting in reverse.
Connection 1) Rc connection Confirm that chips from the pipe threads and sealing material do not enter the piping. Also, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads. -4- Piping Piping 2) TSJ connection The TSJ fitting is a kind of a self-align fittings.
Operating Environment Warning (1) Do not operate under the conditions listed below due to a risk of malfunction. In locations having corrosive gases, organic solvents, and chemical solutions, or in locations in which these elements are likely to adhere to the equipment. In locations in which salt water, water, or water vapor could come in contact with the equipment.
Do not service or attempt to remove pr confirmed. 3. Do not service or attempt to remove pr confirmed. 3. Do not service or attempt to remove pr 3. Do not service or attempt to remove pr 3.
Do not service or attempt to remove confirmed. 3. Do not service or attempt to remove confirmed. 3. Do not service or attempt to remove 3. Do not service or attempt to remove 3.
Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Note 1. The power supply should be off while setting the switches. 2.
Red flashing SI unit has detected the transmission rate, but is not addressed by the DP master OFF Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.