VCB Cannot be used as an emergency shutoff valve, etc. The valves presented in this catalog are not designed for safety applications such as an emergency shutoff valve. If the valves are used in this type of system, other reliable safety assurance measures should also be adopted. 2.
Insert each lead wire into the corresponding connector number by following the chart provided below. 20 mm or more Connector no.
When the valve is secured using an insert nut (part number suffix -N), handle with care during installation because the application of excessive stress to the body could damage it (appropriate tightening torque: 0.8 to 1.0 Nm). 1.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 1.
This may also have an adverse effect on the peripheral equipment in proximity. Should a valve be continuously energized for long periods, or its daily energized state exceeds its non energized state, please use an energy saving type AC, energizing for long periods of time continuously, select the air-operated valve and use the continuous duty type of the VT307 for a pilot valve.
less 250 x 250 18 625 or less 282 Body size under 100 to 150 350 or less 300 x 300 20 900 or less 339 20 to 350 under 150 to 200 400 or less 23 Over 900 under 200 to 250 450 or less Order a thickness equal to or greater than that shown on the table.
A 47 58 B 35 40.5 QA 6 8 QB 13 16 QV 33 38.5 Bore size (mm) 40 50 20 Series RSG Rod End Configuration Lever Type with Integrated Shock Absorber Basic type/Flange mounting These drawings (2 items) show the piston rod extended. Direction of work piece conveyance RSG-L Bore size: 40, 50 (98 + Stroke) Stroke 20 A 4-9 through 110 + Stroke 177 + 2 Strokes 67 + Stroke Approx.
or less 0.1MPa 0.15MPa Single 3.2 (0.18) SQ1230 15 or less 80 Metal seal 0.18MPa 0.18MPa Double (latching) Double (latching) Minimum operating pressure 4.5 (0.25) SQ1231 20 or less 80 Rubber seal 0.1MPa 0.1MPa Double (double solenoid) 3.2 (0.18) SQ1230D 10 or less 95 Metal seal 13 or less 0.1MPa 0.2MPa Double 3 position (double solenoid) 4.5 (0.25) SQ1231D 15 or less 95 Rubber seal 20
Please note, when selecting a product without an auto switch(es) (excluding those with built-in magnet), it is not possible to mount an auto switch(es) following receipt of the product from an SMC factory. Mounting Caution All models 1. In high humidity environments, keep the valve packed until the time of installation. 2.
Do not use this product in an area that is dusty, or in an environment in which water or oil splashes on to the cylinder. Caution 1. Martensitic stainless steel is used for the finger guide, so make sure that anti-corrosiveness is inferior to the austenitic stainless steel.
It is illustrated with an arrow pointing towards the valve body or an "empty" triangle on the schematic. OUTLET (Downstream) is defined as a port connected to the region above the seat and below the diaphragm.
Pull a new element by the cloth handle toward the center, and put it inside the basket, folding the edge of an element. Further, push the edge of an element to the basket s bottom-plate flange surface thoroughly. Tightening bolt Stopper Basket Edge of the element 1-4. Remove the cover upward by turning it counterclockwise.
Install an air dryer or after cooler on the upstream side of the pressure release 3 port valve because air containing excessive drainage may cause malfunction. SA VA SA Model VHS20 VHS30 Effective sectional area (mm2) (Cv) 5 (0.27) 5 (0.27) Caution VA 3. Do not apply negative pressure. It may result in malfunction. 1. Install an air filter of 5 mm filtration on the inlet side. 2.
Can hold an intermediate cylinder position for an extended time. Drop prevention Applicable solenoid valve VQ4 1 2 VQ44 If the double check spacer with a built-in double check valve is combined, it will enable the cylinder to stop in the intermediate stroke and maintain its position for a long time without being affected by the leakage between the spools.
o uss cl63n liltrd an the supPly eurrent 4-wire: Input signal of 0-20(mA) Power supply ot l215(V) Current 4-wire: 0-20 mA Input impedance: 200(c,) quivalent 3 TheAir Filterand Nrist SeDaratorshould be maintained periodically.
Pull a new element by the cloth handle toward the center, and put it inside the basket, folding the edge of an element. Further, push the edge of an element to the basket s bottom-plate flange surface thoroughly. Tightening bolt Stopper Basket Edge of the element 1-4. Remove the cover upward by turning it counterclockwise.
o uss cl63n liltrd an the supPly eurrent 4-wire: Input signal of 0-20(mA) Power supply ot l215(V) Current 4-wire: 0-20 mA Input impedance: 200(c,) quivalent 3 TheAir Filterand Nrist SeDaratorshould be maintained periodically.
IISA2NPL-1D1 set (1 station manifold part number) ISA2-GE41N 1 set (Air catch sensor part number) Prefix the part number of the air catch sensor with an asterisk (). Prefix the part number of the air catch sensor with an asterisk ().
36 132 50 41 200 74 60 230 74 60 271 86 70 22 36 110 180 544 612 873 JIS Symbol 1 4 1 2 2 Construction/Parts/Dimensions ANA1-01 to 06 Sound absorbing Case material (PFV ) End plate Hexagonal flats ANA1-06: PP How to Order Cover ANA1-10 to 20 Sound absorbing material Body Tension bolt End plate A1 03 AN Port size Symbol Connection Port size 1 8 01 1 4 3 8 1 2 3 4 02 03 04 06 10 12 14 20 (
Install an air drier or aftercooler before the product. Caution (1) When the element becomes clogged at an early stage, please check the air quality.