I/O Configurator (NFC version) Do not connect multiple NFC readers / writers to a PC. Connection details of the I/O Configurator for NFC and the wireless unit Before the wireless system can be used, it is necessary to pair each Remote with its Base using the I/O configurator for NFC. The following sections of this document should be read before using the I/O configurator for NFC; 2.
Do not connect multiple NFC readers / writers to a PC. Connection details of the I/O Configurator for NFC and the wireless unit Before the wireless system can be used, it is necessary to pair each slave with its master using the I/O configurator for NFC. The following sections of this document should be read before using the I/O configurator for NFC; 2.
DO (n+1) Output interface Short circuit protection 0 V DO (n) FE / Shield Output circuit / Bus interface 24 V (logic / sensors) 0 V (logic / sensors) 24 V (valves / loads) 0 V (valves / loads) FE BUS . 8-3 EX245-DY1 60 No.EX-OMU0020CN 9.
Do not connect multiple NFC readers / writers to a PC. Connection details of the I/O Configurator for NFC and the wireless unit Before the wireless system can be used, it is necessary to pair each slave with its master using the I/O configurator for NFC. The following sections of this document should be read before using the I/O configurator for NFC; 2.
for mounting attachment) 46 58 45 45 42 26H9 + 0.052 depth1.5 0 30 Positioning pin hole 60 18 5 86 30 107 Auto Switch Mounting Groove Dimensions M5 x 0.8 (Finger opening port) 14 24 M5 x 0.8 (Finger closing port) 42 8 3 4 3 MHY2-25D2 Opening/Closing direction through-hole type 4 x 5.5 through (Hole for mounting attachment) 12 -0.005 -0.025 6 12 22.5 (Limted area for mounting attachment) Do
When air is supplied to all ports after the solenoid valve is pressure-center positioned, the pistons for rotary operation do not have any thrust, as the pressure in both sides is equal, and the pistons for rotary operation move to the center position due to the thrust of the pistons for center stop.
Do not place your fingers in the clearance between the non-rotating plate and the cylinder tube. Your fingers could get caught between the table and the cylinder tube when the piston rod retracts. If fingers are caught in a cylinder, there is a danger of injury due to the strong cylinder output, and therefore, caution must be exercised. 2.
Do not apply torque directly to the rod. Carbon steel Nickel plated Rod end nut !0 * NBR Rod seal !1 * NBR Piston seal !2 * NBR Tube gasket !3 Note 1) 12: Aluminum bearing alloy. Replacement Parts: Seal Kits Bore size (mm) Kit No. Contents CQSKB12-PS 12 CQSKB16-PS 16 Kits include items !1, !2 and !3 from the table above. CQSKB20-PS 20 CQSKB25-PS 25 *Seal kits consist of items !1, !
Caution Aluminum alloy cast (Steel tubing: Cast iron) Chromated (In case of aluminum alloy cast iron) Non-lube Piston Chromated (In case of aluminum alloy cast iron) Aluminum alloy cast (Steel tubing: Cast iron) Air-hydro Weight/Aluminum tube: Lube style (Non-lube style, Air-hydro style) (kg) Do not open the cushion valve excessively.
Adjust the opening/closing speed of the fingers with a speed controller so that they do not operate any faster than necessary. When fingers open and close faster than necessary, impact on the fingers and other parts increases, causing poor repeatability when gripping workpieces and danger of an adverse effect on the product's life. MRHQ25C P408080-3C 2.
Do NOT make upward piping. qFloat style auto drain (N.O.) 1)Use compressor with capacity more than 3.7kw{400L/min (ANR)}. 2)Set pressure more than 0.1MPa wFloat style auto drain (N.C.) 1)Compressor can be used even if energy is under 3.7kw. 2)Set pressure more than 0.15MPa wFloat style auto drain (N.C.) DO NOT pipe upwards. 1.4-13
W With locking at head side With locking at rod side q Do not use a 3 position solenoid valve. Avoid using circuit with 3 position solenoid valve (especially closed center). When pressure is trapped in the port with locking mechanism, end lock is free.
The resulting impact cannot be absorbed easily, the stroke position cannot be maintained, and faulty operation may result. t Lubrication The bearing can be used in an oilless state, but when you are going to oil the bearings, do so by using a ball-cup so that no foreign matter will be mixed.
Do not over tighten the lock nut. 4.7-7 Series ML1 Basic Style Bottom side piping port size Mounting side should be processed according to the dimensions below.
Do not service machinery/equipment or attempt to remove component until safety is confirmed. 1) Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 4-17-4
Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). Also, since there is a breathing port for the armature in the manual override part, do not allow accumulation of dust and/or other foreign materials to block bleed port.
Also, since there is a bleed port for the armature in the manual override, do not allow accumulation of dust and/or other foreign materials to block bleed port. Change of Electrical Entry Angle 1. Series VT317 can change electrical entry angle. (4 positions) 2.
Do not use any sealing agent other than seal tape. Design Warning 1. Please contact SMC when fluids other than air are used. 2. Do not supply air pressure from 2(A) port. The air will leak out from 1(P) port. 3. Since the valve allows a small volume of air leakage, it may not be suitable for holding pressure in a pressure vessel.
You do not need to specify "N" (i.e., without lead wire) for D-A3A, D-A44A, D-G39A, and D-K39A. This is the only standard specification automatically available for these models.
Note 3) Do not add value to long stroke models. 4 Compact Cylinder Series CQS Accessories Single knuckle joint Double knuckle joint ND hole H10 axis d9 L MM MM NDH10 RR1 RR1 E1 E1 NX NZ A1 U1 L1 A1 U1 NX L1 A A Metric Threads Metric Threads ND H10 NX Pin part No. NDH10 NX Bore size (mm) Bore size (mm) E1 A1 MM U1 Part No. A Part No.