Rotary Actuator Failure to do so may cause the angle adjusting screw to become loose or drop.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water vapor, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Do not allow pallets to strike the lever when it is standing up. Do not allow pallets to strike the lever when it is standing up (after the shock absorber has absorbed energy), because the cylinder body will be subjected to the full energy of the impact. 2. Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc.
Rotation should be controlled by connecting it to another shaft (linear guide, etc.). 3.Do not operate with the magnetic coupling out of position.
Sensor shall be inspected by experienced person with adequate knowledge. (2) Do not overhaul nor modify to avoid electric shock, failure, fire, etc. Overhauled or modified product does not guarantee spec. function or performances. Warning Handling ! (1) Do not drop, hit nor apply excess impact(100m/s2 or more).
Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. 2. If using in a location directly exposed to sunlight, shade the product from the sunlight. 3. Do not mount the product in locations where it is exposed to radiant heat. 9 4. Do not use the product in a place where static electricity is a problem.
However, do not use the product under water.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
Do not use any form of sealant other than the tape type of sealant. 3Winding of sealant tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not enter the piping.
Precautions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
It may cause injury to personnel. 5) Do not use the product to clean or remove toxic substances or chemicals. 6) Do not drop, step on or hit the product.
Do not use tubing which do not meet these outside diameter tolerances. It may not be possible to connect them, or they may cause other trouble, such as air leakage or the tubing pulling out after connection. -14SY3000*-OMJ0003-A Specific Product Precautions 8 Be sure to read before handing.
Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Low-frequency operation 3.
Note) Do not pull on the lead wires with excessive force. This can cause faulty and/or broken contacts.
Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. Operate after safety is confirmed. 5. If the volume of air leakage increases or the valve does not operate normally, do not use the valve.
Do not disassemble the product or make any modifications, including additional machining. Doing so may cause human injury and/or an accident. 14.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Operation of auto drain will stop and water will flow out through the air outlet.) When tightening piping at the air inlet/outlet tube, the nozzle should be held firmly with a pipe wrench.
Do not use in these conditions. (Refer to specifications.) Consult SMC if a fluid other than compressed air is used. 2.