AIR GRIPPER

Max. tightening Maximum screw-in torque depth Model Bolt Depth [mm] (Nm) JMHZ2-8 M3 x 0.5 0.88 6 JMHZ2-12 M3 x 0.5 0.88 6 JMHZ2-16 M4x0.7 2.1 8 JMHZ2-20 M5 x 0.8 4.3 10 Max. tightening Model Bolt torque Nm JMHZ2-8 M2.5x0.45 0.31 JMHZ2-12 M2.5x0.45 0.31 JMHZ2-16 M3 x 0.5 0.59 JMHZ2-20 M4x0.7 1.4 7 - ! Caution 1.

MHx-OMU0057

5.9 10 MHZ2-32 M61 5.9 10 MHZ2-40 M81.25 13.7 13 Nm Lmm MHZ2-10 M30.5 0.69 5 MHZ2-16 M40.7 2.1 8 MHZ2-20 M50.8 4.3 10 MHZ2-25 M61 7.3 12 MHZ2-32 M61 7.9 13 MHZ2-40 M81.25 17.7 16 Nm MHZ2-10 M2.50.45 0.49 MHZ2-16 M30.5 0.88 MHZ2-20 M40.7 2.1 MHZ2-25 M50.8 4.3 MHZ2-32 M50.8 4.3 MHZ2-40 M61 7.3 D-Y59 D-Y69 D-Y7P 7 - 1. 2. 1. 2. 3. 8 - 3. 4. 10 2 16 2 1 <> : AS1211F-M3 AS1201F-M5

MHx-OMZ0004

M6x23 : : M3X7 D-M9P-5 JMHZ2-16D M-5ALHU-2 2 KQ2S04-M5N 3 V114-5LU ASN2-M5-X937 3x6 ISO9409-1 M4x25 6x10 M6x10 M8 8 () M6x10 ISO9409-1 6x10 5 - 3-1. JMHZ2-16D-X7400B-ASSISTA(-P) mm 16 MPa 0.1~0.7 (oC) -10~50 (mm) 0.01 (c.p.m.) 120 32.7 (N) 43.5 (mm) 10 (g) 680 D-M9(N/P)-5 ISO9409-1-31.5-4-M5 (www.smcworld.com)JMHZ2 Series P .15 M12 8 6 - 3-2. 2 1 F 7 - 3-3.

Air Gripper for Collaborative Robots

Parts description of the air gripper JMHZ2-16D-X7400B-DTP-(N/P) Hexagon socket head cap screwsM6x23 Attachments Hexagon socket head cap screws M3X7 Auto switches D-M9(N/P)-5 Air gripper JMHZ2-16D Positioning pins3x6 Miniature Fittings: M-5ALHU-2 Adapter plate Polyurethane Tubings: O.D.2 One-touch fitting KQ2S04-M5N Metering Valve with Silencers: ASN2-M5-X937 3-port solenoid valves: V114-5LU

DOC1023125

Work piece fixed Maximum tightening Model Bolt size Max.thread torque [Nm] depth (mm) EQFS25 M5 x 0.8 3.0 8 EQFS32 M6x1 5.2 9 EQFS40 M8 x 1.25 12.5 13 Use screws with adequate length, but with length less than the maximum thread depth. The use of screws that are to long can touch the body and cause malfunction.

LEF-OM002xx

(Only "With motor cover") (Nm) M2.5 0.3610% M3 0.6310% M4 1.510% M5 310% The fingernail of "Grommet" is inserted in the hole of "Pulley box". Grommet 43 - 7. Troubleshooting Alarms below are abstract of representative examples. For other alarms, see operation manual of controller. No.

Electric Actuator / Slider Type 《 AC Servo Motor 》

Bolts Size Tightening torque (Nm) M3 0.6310% M4 1.510% M5 310% 8.Troubleshooting When a fault occurs during the operation, the corresponding alarm or warning is displayed.

SFOD-OMT0009CN

) (M5)X4 (b) DIN DIN DIN (M5X8) DIN 2 4 3.0[Nm] M5X8 DIN 1 2 2 3.0[Nm] DIN M5X14 A DIN B DIN DIN (M5X14) 0.40.6 [Nm] 0.40.6[Nm] 28 No.SFOD-OMT0009CN-B A B M5X14 (2) M3 29 No.SFOD-OMT0009CN-B (1) D (100) 2 (2) 2mm D : : (3) 40 50mm ()100mm , 100 30 No.SFOD-OMT0009CN-B 5. 5.1 (1) C PWR +24V 24-0V +24V (+) (+) (24-0V) (-) (-) JXC-C1 2) AWG20(0.5mm 1.76 +24V 24-0V (

JXCx-OMT0001CN

LED LED OFF IP NS EtherNet/IP IP OFF MS EtherNet/IP LED 10Mbps P2-100 EtherNet/IP 100Mbps / P2-L/A / / / 10Mbps P1-100 EtherNet/IP 100Mbps / P1-L/A / / / -29No.JXC-OMT0001CN-C 4.4. 1 2DIN -30No.JXC-OMT0001CN-C 4.5 (1) DIN (A) (M5 4 ) (M5)X4 () (b) DIN (DIN ) DIN M5X8DIN 2 4 (:3.0[Nm]) M5X8 (M5X14)1 DIN 2 2 :3.0[Nm] DIN () A DIN B M5X14 M5X14) DIN (:

KQ-OMS0022

By chamfering as shown in the following table, machining of threads is easier and effective for burr prevention. 2Specific Product Precautions (5) Caution (1) Connection thread: M5 and 10-32UNF First, tighten by hand, then use a wrench appropriate for the hexagon flats of the body to tighten an additional 1/6 to 1/4 turn. A reference value for the tightening torque is 1 to 1.5 Nm.

Metal One-touch Fittings

Connection Thread Tightening Method Caution (1) Connection thread: M5 and 10-32UNF First, tighten by hand, then use a wrench appropriate for the hexagon flats of the body to tighten an additional 1/6 to 1/4 turn. A reference value for the tightening torque is 1 to 1.5 Nm. Note) Excessive tightening may damage the thread portion or deform the gasket and cause air leakage.

EtherNet/IP TM Compatible Fieldbus System

EX500-DXPB Install the product using 2 M5 screws x 20 mm or longer with a head 9 to 11. 51 No.EX-OMS0014-A Wiring EX500-DXPA Branch wiring Connect the branch cable to the branch connector (IN/OUT). Refer to page 12 for wiring. Sensor wiring Connect the sensors to the sensor connectors. Pin layout of the sensor connector M8 connector (3 pin, socket) No.

Solenoid Valve

Otherwise, air leakage may result. 2) After screwing in the fittings, mount the M5 fitting assembly on the manifold base.

IDX-OM-W028

IDU Series 10-1 Safety instructions 10 1 IDX-OM-W028 Air Dryer 10 Specification for Option R IDU22E75E-23 IDU22E75E-30 Customer connection side Tightening torque : M5 (2.6Nm) Connector width : 9.5mm or less Applicable electrical wire1.25mm2 or more Customer connection side Tightening torque : M5 (2.6Nm) Connector width : 9.5mm or less Applicable electrical wire1.25mm2 or more L01,L02,L03

V100 Series

For safety, install an appropriate fuse and circuit breaker before use. 1) When using SMCs M5 fittings, follow the procedures below to tighten them. Connection thread: M5 First, tighten by hand, then use a suitable wrench to tighten the hexagonal portion of the body an additional 1/6 to 1/4 turn. The reference value for the tightening torque is 1 to 1.5 Nm 1.

HEC-OM-U015

For example, if -0.15 C is set here, the actual reference temperature for control is lower than the indicated SV by 0.15 C. 5.6 Preparation for facility water M5,M6 screws (bolts) or equivalent to the fix the product.

Fan Type Ionizer

When installing this product with a bracket, secure it with M5 screws using the mounting holes on the bottom of the bracket. (The screws should be Protection film prepared by the user). Refer to "6. Dimensions" for details.

SY3000/5000/7000/9000 Series (Pilot Valve:V100)

Applied voltage When connecting fittings to valves, tighten as indicated below. 1) M3, M5 types 1. When using SMC fitting, follow the guidelines below. After tightening by hand, tighten an additional 1/4 (M3), 1/6 (M5) turn with a tightening tool. However, if miniature fittings are used, tighten an additional 1/4 turn with a tightening tool after tightening by hand.

SYJ Series

Rubber seal, spool valve: Grease Connection thread: M5 Mounting First, tighten by hand, then use a suitable wrench to tighten the hexagonal portion of the body an additional 1/6 to 1/4 turn. The reference value for the tightening torque is 1 to 1.5 Nm. 1.

VEX-OMT0003

M5 First, tighten by hand, then use a wrench appropriate for the hexagon flats of the body to tighten an additional 1/6 to 1/4 turn. A reference value for the tightening torque is 1 to 1.5 Nm. Note) Excessive tightening may damage the thread portion or deform the gasket and cause air leakage. Insufficient tightening may loosen the threads, or cause air leakage.