High Vacuum L Type Valve When multiple heater assemblies or valves are used, do not apply power to the heater assemblies simultaneously. Keep approximately 30 seconds between applications of power to each heater assembly. This will allow for incremental spacing to prevent harmful large initial surge. 8 XL*-OMI0011-E 4.
Do not operate at pressures or temperatures, etc. beyond the range of specifications, as this can cause damage or malfunction. (Refer to specifications.) Contact SMC when using a fluid other than compressed air (including vacuum).
Do not operate in locations having an atmosphere of corrosive gases, chemicals, sea water, water or steam, or where there will be contact with the same. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Do not touch the cylinder during operation at a high speed and a high frequency. Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 2. Do not use the air cylinder as an air-hydro cylinder.
Therefore, do not loosen or remove the hexagon socket head cap screws which secure cover A and cover B. 2. Be sure to contact SMC regarding disassembly or repair, etc. D-X Individual -X 779
Electrical entry T -With conduit terminal TL -With conduit terminal and light D -DIN terminal DL -DIN terminal with light DO-For DIN terminal (without connector, gasket is included.)
Do not use for intermediate stops while the cylinder is operating. This cylinder is designed for locking against inadvertent movement with the locking mechanism from a stationary condition. Do not perform intermediate stops while the cylinder is operating, as this may damage the cylinder, cause unlocking malfunction or shorten the service life. 3.
How to Order XC4 With heavy duty scraper Specifications: Same as standard type Dimensions: Same as standard type Caution Do not replace heavy duty scrapers. Since heavy duty scrapers are press-fit, do not replace the cover only, but rather the entire rod cover assembly. Made to Order Related Products 150 CP96 Series Symbol -XC7 Tie-rod, Tie-rod Nut, etc.
Our pressure switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 3. Do not use in an environment where static electricity can cause problems, otherwise system failure or malfunction may result. 1. Do not drop, bump, or apply excessive impacts (980 m/s2) while handling.
Do not use in atmospheres where the valve is in direct contact with corrosive gases, chemicals, salt water, water or steam. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications in the main section of the catalog. 4. Use a protective cover, etc., to shield valves from direct sunlight. 5.
Do not use the product in a place where it could be splashed by oils or solvents. 1. Do not drop, bump, or apply excessive impacts (100 m/s2) while handling. Although the body of the sensor may not be damaged, the internal parts of the sensor could be damaged and lead to a malfunction. 2.
Do not exceed the screw-in torque of 7 to 9 Nm when connecting the pipe to the switch. Exceeding these values may cause the switch to malfunction. 4. Do not use pressure sensors with corrosive and/or flammable gases or liquids. 5. Allow a sufficient margin of tube length in piping in order to prevent application of torsional, tensile or moment load to the tubes and fittings. 6.
Do not use in explosive atmospheres. 2. Do not use in locations subject to excessive vibration or impact. Impact resistance of this solenoid valve is 150 m/s2. Vibration resistance of this solenoid valve is 30 m/s2. 3. Do not use in locations where radiated heat will be received from nearby heat sources.
Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals etc. will result in leakage or malfunction.
Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions.
Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Error Name Error Display Error Type Troubleshooting Method Turn the power off and remove the output factor for the over current. Then turn the power on.
Claw 1 Claw 2 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Error Name Error Display Error Type Troubleshooting Method [2] Turn the power off and remove the output factor for the over current. Then turn the power on.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. This function is to display error location and content when a problem or an error occurs. Error name Error display Error type Troubleshooting method Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.