PVC Quick Drain Valve Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiation heat. 4. Do not use in environments which exceed the ambient temperature specifications of the product. Caution 1.
Operating pressure Do not use the product beyond the operating pressure range. Do not use in locations where peak pressure exceeds the operating pressure due to water hammer, surge pressure, etc. FGC Bag filter FGF FGF Fluid release valve Tank FGH 2. Operating temperature Do not use the product beyond the operating temperature range.
Do not touch the cylinder during operation. Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 4. Do not use an air cylinder as an air-hydro cylinder. If it uses turbine oil in place of fluids for cylinder, it may result in oil leakage. 5.
Do not use in an atmosphere where corrosive gas es, chemicals, sea water, water, or water steam is present. Do not use in cases where there is direct contact with any of the above. 2. Maintenance space Allow sufficient space for maintenance and inspection. 2. Do not use in a place subject to heavy vibration and/or impact. 3. Observe the tightening torque for screws.
Do not operate or set with wet hands. This may lead to an electric shock. End plate bracket (EX600-ZMA2) SUPPLIERS DECLARATION OF CONFORMITY Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Connector (Base only) (2) Add more units.
Colour of cover Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
[F 0] Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction or damage to the product can result. Verify the specifications before use. [ Un i] Unit selection function 1 [ L] L/min Default settings When the flow exceeds the set value [P_1], the switch will be turned ON.
Set value Set value or 3 4 or 3 Accumulated pulse Time ( ) U P Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. 4 1 2 U P Flow DOWN DOWN 4 3 DOWN Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Panel mount adapter (Part number: ZS-26-B) Front protective cover (Part number: ZS-26-01) [F20] Setting of external input Accumulated flow external reset [F22] Setting of analogue output Free range analogue output for instantaneous flow: OFF * Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not allow humans or objects to touch the ionizer while power is being supplied. Otherwise, the offset voltage may change or the HV LED may turn ON. 14. Do not make a rapid pressure change while power is being supplied to the ionizer. It will cause the NDL LED to turn ON. 15. Do not use this product in an enclosed space. This product utilizes the corona discharge phenomenon.
Do not allow humans or objects to touch the ionizer while power is being supplied. Otherwise, the offset voltage may change or the HV LED may turn ON. 14. Do not make a rapid pressure change while power is being supplied to the ionizer. It will cause the NDL LED to turn ON. 15. Do not use this product in an enclosed space. This product utilizes the corona discharge phenomenon.
Do not allow it to idle for a long time. If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling for 3 minutes or longer. 10.
Do not use in an atmosphere where the electro-pneumatic proportional valve is in direct contact corrosive gases, chemicals, salt water, water, steam. 2. Do not use in an environment where flammable gas or explosive gas exists. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 4.
No output Reduction of the set pressure Unstable set pressure Delay in increase of the downstream pressure Operating environment Warning (1) Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. (2) Do not operate in a location subject to vibration or impact.
No output Reduction of the set pressure Unstable set pressure Delay in increase of the downstream pressure Operating environment Warning (1) Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. (2) Do not operate in a location subject to vibration or impact.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these . 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. Warning 5 VN-OMA0013-D VND Series Valves for Fluid Control Specific Product Precautions 1 Be sure to read this before handling.
In particular, use a pair of ultra-mini pliers such as the Super Tool CSM-07A for removing and installing the snap rings on the 10 cylinder. r In the case of auto switch rail mounting style, do not remove the rail that is mounted.
Do not operate in locations with an atmosphere of corrosive gases, chemicals, sea water, water or steam, or where the same substances will adhere to the regulator. 2. Do not operate in locations where vibration or impact occurs. 3. In locations under direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off the radiated heat. 5.
MK/MK2 RSQ/RSG RSH q Do not operate the cylinder horizontally. w Do not perform work in the rotational direction. CE1 CE2 ML2B ML1C REA REC Figure 3 Figure 4 RHC e Do not clamp during a rotational stroke. MTS CC Figure 5 t Make sure that the workpiece does not move during clamping. r Do not clamp on a slanted surface.