DOC1003626 The received message is deleted if the calculation result and received CRC do not match.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications in the main section of this catalog. 4. A protective cover, etc. should be used to shield valves from direct sunlight. 5.
DIN connector (Without connector) 04 1 2 1 2 AN 04 5 06 1 2 3 4 1 2 3 4 1 Body ported G Grommet (300mm lead wire) AMC 10 1 1 1 H Grommet (600mm lead wire) E Grommet terminal 10 7 12 14 9 20 2 Wihout subplate 1 4 1 T Conduit terminal D DIN connector 1 4 1 2 1 2 G Grommet (300mm lead wire) Grommet (600mm lead wire) DIN connector DIN connector(Without connector) 2 01 1 8 1 8 H D DO Base mounted
NO YES Do you have any problem, even if it might run over the target position? (Overrun) NO Do you have any problem, although an error might occur if it is set to be (number of trial again = 0) in order to prevent from doing a trial again when positioning is done at the outside of the range? During the positioning operation, there may be the case it needs to do overruns or trials again.
Do not use compressed air that contains chemicals, synthetic oils including organic solvents, salt or corrosive gases, etc., as it can cause damage or malfunction. 4. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 5.
Do not use valves in such environments where corrosive gases, chemicals, or brine or water or steam is airborne, or where valves can be directly exposed to any of those. 2. Do not use in locations influenced by vibrations or impacts. 3. This vacuum regulator always uses atmospheric air, therefore, do not use in dusty environments. 4.
They do not guarantee an actual fixed range (expect approximately 30% dispersion).
In a locked state, do not apply impacts, strong vibrations or rotational forces. Do not apply a impacts, strong vibrations or rotational forces from external sources, because this could damage or shorten the life of the lock unit. 4. The locking of the fine lock cylinder is directional.
In a locked state, do not apply impacts, strong vibrations or rotational forces. Do not apply a impacts, strong vibrations or rotational forces from external sources, because this could damage or shorten the life of the lock unit. 4. The locking of the fine lock cylinder is directional.
Applicable model t ZH15DA-09-N03-11 ZH15DA-N02-N03-N03 2 Minimum C Factor of a Supply Valve Model C[dm3/(sbar)] ZH05A 0.12 ZH07A 0.23 ZH10A 0.47 ZH13A 0.80 ZH15A 1.06 ZH18A 1.53 ZH20A 1.88 ZH18DA-11-N03-13 ZH18DA-N03-N03-N03 1 ZH20DA-10-04-12 ZH20DA-03-04-04 ZH20DA-11-N04-13 ZH20DA-N03-N04-N04 t 2.
DO Without connector Note) Do not replace V111 (G, H, L, M) to V115 (DIN terminal) and vice versa when replacing pilot valve assembly only. 5 SY3000/5000/7000/9000 Body Ported How to Order Port Block Assembly 000 6A SY Series Thread type 3 SY3000 5 SY5000 7 SY7000 9 SY9000 Only replacement of the fittings assembly is possible.
Do not apply negative pressure. It may result in malfunction. Should they remain, they could cause malfunction. 3. When connecting pipes and fittings, etc., be sure 3. Do not supply air pressure from ports other than that neither chips from the pipe threads nor sealing material get inside the valve.
Model CYP15 CYP32 Series Throttle valve 10-AS2200-01-X214 Elbow type 10-AS1200-M5-X216 Metal body piping type 10-AS2000-01-X209 In-line type 10-AS1000-M5-X214 10-AS2201F-01-04-X214 10-AS1201F-M5-04-X214 Elbow type (throttle valve) 10-AS2201F-01-06-X214 10-AS1201F-M5-06-X214 10-AS2201F-01-06-X214 Operation 10-AS2301F-01-04-X214 10-AS1301F-M5-04-X214 Resin body with One-touch fitting Caution
-G AV4000-04-GS AV4000-04-D AV4000-04-DZ AV4000-04-Y AV4000-04-YZ AV5000-G AV5000-GS AV5000-D AV5000-DZ AV5000-Y AV5000-YZ M4 x 0.7 Depth 4.5 VY1 22 29 0 38 40 31 105 93 66 1/4 47.5 23.5 65.5 6 M4 x 0.7 Depth 4.5 G 22 29 0 38 40 31 125 66 1/4 23.5 82.5 23 67.5 10.5 M4 x 0.7 Depth 4.5 PPA 22 29 0 38 40 31 125 66 1/4 23.5 84.5 27.5 M5 x 0.8 Depth 5 AL 24 28 2 43 48 36 112 100 76
(Do not tighten with pliers.)
(Do not tighten with pliers.)
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.