IDX-OM-W013 For safety operation of SMC Refrigerated Air Dryer, read thoroughly and follow stated safety instructions, as well as regulation stated within ISO 4414*1 & JIS B 8370*2. *1) ISO 4414: Pneumatic fluid power General rules and safety requirements for systems and their components *2) JIS B 8370: Pneumatic fluid power General rules relating to systems This manual explains about installation
A B A B A B A B A B A B A B A B A B 40 50 63 80 100 6 4 4 1 0.5 0.5 1 7 2.5 4.5 12 10 0 0 4 0 1.5 9 8 3.5 6 4 3.5 1.5 1 0 0.5 6.5 2 4 11.5 10 0 0 4.5 0 2 9.5 8 3 8.5 7.5 6 5 4.5 2.5 3 9 4.5 6.5 14 12.5 1.5 2 8 3.5 5.5 13 11.5 5.5 12 10 9.5 7.5 7 6 6.5 12.5 8 10 17.5 16 4 4.5 10.5 6 8 15.5 14 9 13.5 12.5 11 10 9.5 7.5 8 14 9.5 11.5 19 17.5 6.5 7 13 8.5 10.5 18 16.5 10.5 Note) Adjust the auto
b . A b . A b . A 1 2 3 1 b012 Ab. 0 1 b b . A b .
END 1014 Booster Regulator VBA Series Working Principle The IN air passes through the check valve to booster chambers A and B. Meanwhile, air is supplied to drive chamber B via the governor and the switching valve. Then, the air pressure from drive chamber B and booster chamber A are applied to the piston, boosting the air in booster chamber B.
F,N)06A,B(-B,S)(-K,R,Z) VHS5510-(F,N)06~10A,B(-B,S)(-R,Z) Contents PAGE 1.
HED003-W2 A B 13 19 HED003-C2A B (Temperature Controller) HED003-HW13 19 (Heat Exchanger) HED005-W2 A B 13 19 HED005-C2A B (Temperature Controller) HED005-HW13 19 (Heat Exchanger) HED007-W2 A B 13 19 HED007-C2A B (Temperature Controller) HED007-HW13 19 (Heat Exchanger) Keep this manual available whenever necessary.
END 5 Booster Regulator Series VBA Working Principle The IN air passes through the check valve to booster chambers A and B. Meanwhile, air is supplied to drive chamber B via the governor and the switching valve. Then, the air pressure fromdrive chamber B and booster chamber A are applied to the piston, boosting the air in booster chamber B.
r B " " $6y t " 5 ' % " $60C4,D 4 B u % " " B 17-3-98 Series VVXA21/22 Direct Air Operated 2 Port Valve/Manifold For Air, Gas, Vacuum and Oil The VX series will be revised shortly.
AP100 17 735 ARM11A/B Series Pressure Switch Block 56 ARM11AW Z A 0.4 0.2 0.6 0.5 20 MPa 24 q w 0.3 0.1 1. Accessory 2.
For safe operation of SMC Thermo-dryer, thoroughly read and follow the safety instructions, as well as regulations stated within ISO 4414*1 & JIS B 8370*2. *1) ISO 4414: Pneumatic fluid power General rules and safety requirements for systems and their components *2) JIS B 8370: Pneumatic fluid power General rules relating to systems This manual is intended to explain the installation and
This item is U n i t N u m b e r M O D E < 0 applicable only when multiple units are used. 2. Baud Rate B a u d R a t e M O D E < 1 2 0 0 b / s Setting range : 600, 1200, 2400, 4800, 9600, 19200b/s Indicated content : Baud rate (Ex. : 1200b/s) Function : Sets baud rate for communication. 3.
H Non-leak (105atm cc/sec) Brake oil Water (Up to 60C) B P A H Stainless Steel Note 1) The leakage amount(105atm cc/sec)of "V" option is valued when differential pressure is 0.1MPa.
Analog Output Flow/Analog output Output A B C Voltage output 1 V 1.1 V 5 V Current output 4 mA 4.4 mA 20 mA C Model Rated flow [L/min] Minimum Maximum LFE1 0.5 20 LFE2 2.5 100 LFE3 5 200 B A Outside the range 0 Min.
0.2 0.1 0.2 C and b values are for controlled flow with the needle fully open and free flow with the needle fully closed.