<br>
<br>Note) The KK□ series S coupler cannot be used as a stop valve that requires zero leakage. Due to the specifications of the product, a certain amount of leakage is unavoidable.<br><br>
<br>Note 3) If the surge pressure is higher than the max. operating pressure, it may cause damage to the fitting or tube.<br><br>
<br><br>Meter-in control is a control method in which the speed of the cylinder is controlled using the cylinder supply flow rate.<br>With meter-in control, the exhaust conditions do not affect operation, and the piston can start moving quickly. (Cylinder lurching can be prevented.)
<br>Note) The accuracy will decline if IN side piping deviating from the recommended straight piping length or bore size is used.<br><br>
<br>The VX3 series catalog can be found here.<br><br>
<br>Be sure to check the specifications and precautions listed in the catalog of each type of tubing and fitting. <br>Note that LQ series piping requires a special tool. <br><br>
<br><br>Fittings and tubing catalogs can be found here.
Further details on the PA/PAP/PAX series can be found <br>In this case, use the bypass piping set (optional accessory) to secure the flow rate. <br>Note) The temperature stability is as follows: ±2.0℃ for the HRSE, ±0.5℃ for the HRS090, and ±1.0℃ HRS100/150/200.<br><br>
<br>First, refer to the “Transport and Setting Up” section in the HRS series operation manual. <br>Wiring examples are shown in the “Wiring of remote operation signal input” and “Wiring of run/stop signal input・Remote signal input” sections. <br>Next, to enable remote signal input, change the communication mode from “LOCAL” to “DIO” mode.
<br>Please check the figure below. If the product is equipped with a control power supply, this control power supply circuit is provided. <br>If the operating power supply voltage is energized while the valve is open, it is acceptable not to drop it to the holding voltage.<br><br>
Magnet: D (Built-in), Mounting: F (Front Flange), Bore Size: 50mm, Port Thread Type: TN (NPT), Stroke: 50mm, Body Option: M (Rod End Male Threads), Locking Direction: B (Retraction Locking), By-Pass Piping: None (Emergency Stop), Auto Switch: M9NWV--Solid State, 2-color Indication, 3 Wire NPN, Vertical, Lead Wire or Prewired Connector: SDPC (0.5m Cord Length, M12-4 Pin Connector)
Magnet: Built-in, Mounting: Front Flange, Bore Size: 50mm, Port Thread Type: NPT, Stroke: 50mm, Body Option: Rod End Female Threads, Standard, Locking Direction: Extension Locking, By-Pass Piping: None (Emergency Stop), Auto Switch: F7BAV--Solid State, Water Resist., 2 Wire, Vertical, Lead Wire or Prewired Connector: 3m
Magnet: Built-in, Mounting: Front Flange, Bore Size: 50mm, Port Thread Type: NPT, Stroke: 50mm, Body Option: Rod End Male Threads, Locking Direction: Retraction Locking, By-Pass Piping: None (Emergency Stop), Auto Switch: M9NWV--Solid State, 2-color Indication, 3 Wire NPN, Vertical, Lead Wire or Prewired Connector: 0.5m Cord Length, M12-4 Pin Connector, Number: -
Title not found *br" *nn I E Fr"r ilbbo" ""d" "o* I EE Fhr'bb-.."d" "o* 10ffoll-s t t l 16 E D Il-@ t t l 16 E D Il-@ Flat ribbon cable conneclor: 26 Dins Flal ribbon cable connecior:20 pins Flal ribbon cable connecror: 10 oins . Tie-rod base SS5V .
<br><br>・While it is possible to mount a G36-10-01 or G46-10-01 pressure gauge on a VEX113□/123□ series regulator, it will be larger than the width of the product body.<br>・It is also possible to mount a G46-10-01 pressure gauge on a VEX133 □ series regulator so long as it does not interfere with the piping.
<br>Note) The all side piping option was only added to the VH200 series (as described in ②) in 2016. The VH series catalog can be found here<br><br>
<br><br>For plug lead type manifolds:<br>The max. number of stations that can be increased depends on the wiring kit.