Proposals for Energy Saving Large diameter piping Small diameter nozzle S1 Pressure loss: Small With nozzle S2 Effective area ratio 2:1 6 Pump capacity Previous rate Pressure Pump head (electric power) Pressure loss: Small P Pump outlet Nozzle outlet Discharge rate Main Points Improve pressure loss. Improve the effective area ratio with the upstream side by using a small diameter nozzle.
Note 4) Kit/Electrical entry/Cable length F P kit (D-sub connector) kit (Flat ribbon cable connector) Note 1) 26P 26P Note 1) Note 1) 25P Side entry Top entry Side entry Top entry Note 1) 25P Connector entry direction Top entry Side entry Connector entry direction Top entry Side entry U0 U1 U2 U3 P. 2-4-76 P. 2-4-78 U0 U1 U2 U3 S0 S1 S2 S3 S0 S1 S2 S3 Without cable With cable (1.5 m) With
S2 S3 U0 U1 U2 U3 U0 U1 U2 U3 S0 S1 S2 S3 S0 S1 S2 S3 (2) Max. 16 stations (2) Max. 16 stations (2) With cable (1.5 m) With cable (3 m) With cable (5 m) With cable (1.5 m) With cable (3 m) With cable (5 m) With cable (1.5 m) With cable (3 m) With cable (5 m) Max. 16 stations Kit P Kit P Kit J Kit J Kit F Kit F L S The valve is equipped with an indicator light/surge voltage suppressor, and
EXH port P1 LED level meter SUP port Sensor S1 S3 Red ON: Output OFF Green ON: Output ON S2 S4 + P2 Redq Detection port Below set position Large clearance S1, S2: Fix orifice S3: Variable orifice (adjusted by setting dial) S4: Detection nozzle Redw BEST POSITION Set position Greenq In a bridge circuit as in the figure above, a detection gap is applied to the detection nozzle (S4) while the
After improvement Before improvement Conventional coil tube model Filter regulator Conventional coupler model S coupler 1 2 1 2 Coil tube L L VMG Air gun Nozzle 2.5 Nozzle 3 S2 S0 to S1 S2 S0 to S1 Effective area ratio 3.04 : 1 Effective area ratio 0.69 : 1 Before improvement After improvement Coupler S coupler Conventional model Piping Equipment TCU1065-1-20-X6 Conventional coil tube model
This connection example complies with the requirement of ISO/EN ISO 13849-1 category 3 PL d. 24 V EMG S4 S3 KM1 S2 KM1 Fuse K3 +24 V XS0 XS1 Z00 Z10 Z20 KM1 Safety relay module MELSEC (QS90SR2S) Pow er supply Control circuit KM1 Driver Servo amplifier X0 COM0 24G X1 COM1 Z01 Z11 Z21 CN8 Control circuit STO1 S1 or EMG (Note) EMG STO2 STOCOM K3 TOFB1 TOFCOM 0 V TOFB2 20 S1: STO shut-off sw
Nil S 1 2 When using an air gripper for AHC, use tool adapter MA3 0-AM3 MHY Tool stand 90 reverse unit MHW MA310 Y59A S1 MA310 90A R1 -X MRHQ Tool stand 90 reverse unit Lead wire length MA Auto switch type Nil L Grommet With 0.5 m lead wire With 3 m lead wire DNil 90 90A Without auto switch D-90 (2 pcs.) D-90A (2 pcs.)
This reduces noise considerably compared with A much lower air consumption is required than the current model. the current model. 1: Conditions: Unseated for 5 seconds and seated for 20 seconds (For G type) Comparison of detection circuit ISA3 New New Current model (ISA2) A B EXH port EXH port P1 Sensor Sensor SUP port S1 S3 SUP port S2 Sensor S1 S4 S2 Detection port P2 Detection port C D
(I.D. 5, equivalent length 5 m) Air gun VMG (Nozzle size 2.5) Conventional model (Nozzle size 3) Coupler, Piping (S0) 13.45 mm2 5.1 mm2 Effective area Air gun (S1) 30 mm2 6 mm2 Nozzle (S2) 4.4 mm2 6.3 mm2 0.69 : 1 3.04 : 1 Effective area ratio (S0 to S1: S2) Impact pressure 0.011 MPa (at a distance of 100 mm) 0.011 MPa (at a distance of 100 mm) Regulator pressure 0.4 MPa 0.5 MPa Pressure
Mounting bolt nut (M2 x 0.4 x 254 pcs.) 1095 Series ZYY/ZYX Ejector Valve Dimensions ZYX3L-S1-EC-MN Silencer Vacuum switch Ejector unit V Release flow rate adjusting needle Supply/Release valve P1 Circuit diagram 6.8 7.4 85 Accessory (packed together) 1. Silencer (AN203-KM81 pc) 51 26 16 2.
The temperature range for the protective label cover is between 40 to 110C, and the temperature range for grease is between 20 to 150C. (However, there is no relationship with the chemicals listed above.) 28 Series CJ5-S/CG5-S Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage.
. 6, 10, 15, 20, 25, 32 Bore size (mm) 10 to 150C Ambient temperature Note 1) Operate without lubrication from a pneumatic system lubricator.
-XB6 3 Heat Resistant Cylinder Specifications MGPM XB6 Bore size Stroke MGPM Applicable series Slide bearing Bearing type Heat resistant cylinder 12, 16, 20, 25, 32, 40, 50, 63, 80, 100 Cylinder bore size (mm) 10 to 150C (14 to 302F) Ambient temperature range Cylinder with modified seal and grease materials to make possible high temperature operation up to an ambient temperature of 150C.
Note 3) It can operate in temperatures between 10 to 150C if there is no risk of the moisture in the air freezing. VEX Refer to page 5-10-13 for Precautions on these products.
Cylinder Specifications Features and Benefits Fluid Air Compact body design for tight spaces Max. operating pressure 150 psi Heat resistant cylinder seals and lubrication Min. operating pressure 7.25 psi Solid-state, heat-resistant switch Ambient and fluid temperature 32 to 300F (0 to 150C) Switch sensor separate from amplifier Operating piston speed 2 to 19 in/s (50 to 500mm/s) Grease
The temperature range for the protective label cover is between 40 to 110C, and the temperature range for grease is between 20 to 150C. (However, there is no relationship with the chemicals listed above.) ) Reference data 848 Series CJ5-S/CG5-S Stainless Steel Cylinder Specific Product Precautions 1 Be sure to read before handling.
-XB6: Heat resistant (15 to 300F) Air cylinder which changed the seal material and grease, so that it could be used even at higher temperature up to 150C. Standard model no. How to Order Note 1) Operate without lubrication from a pneumatic system lubricator.
INFORMATION Heat Resistant 2-Color Indicator Solid State Auto Switch Direct Mounting Type RoHS Heat resistant (Max. 302F [150C]) type added to the D-M9 compact auto switch.
Symbol Specifications XA Change of rod end shape XB6 Heat resistant cylinder (150C) XC3 Special port location XC6 Piston rod and rod end nut made of stainless steel XC8 Adjustable stroke cylinder/Adjustable extension type XC9 Adjustable stroke cylinder/Adjustable retraction type XC11 Dual stroke cylinder/Single rod type XC13 Auto switch mounting rail style XC20 Head cover axial port XC22