Body Size: 200 L/min [ANR], Pressure Range: 0.005 ~0.5Mpa, Fieldbus: EtherNet/IPâ„¢, Thread: NPT, Port: 1/4", 1000, 2000, Made to Order: -
LEC-OM069xx 1 3 Wiring and Connection 3.
Digital Display (3% digit LCO) . Predicted Failure Function . 2 Setpoint Use . High Accuracy O Do not subiect body to excessive exiernal force. O Plping tightening to.ques How To Older (Exampre) 3 4 ( 3 1 3 1 7 ( 1 5 1 5 2 0 ( 1 7 NZXl Nozzle Diameter (Same as Std.) Eiector Exhaust Type (Same as Std.)
*3 *2 *2 *3 *1 Every parameter is set to the recommended condition before shipment from the factory.
*3 *2 *2 *3 *1 Every parameter is set to the recommended condition before shipment from the factory.
When introducing power supply, switch setting will become effective. -17No.EX-OMS0027 Switch setting Settings1 Settings2 1 Hold/Clear setting 1 2 Diagnostics setting 2 3 3 4 4 IP address byte 4 setting DHCP mode setting Reserved 5 5 6 6 7 7 8 IP address byte 3 setting 8 Precautions for handling Handle the switch with care.
(Current consumption of one valve connected to one output x output number) x Output block number = (0.5 A x 2 points) x 3 pcs. = (1.0 A) x 3 pcs. = 3 A Total current consumption = 20 mA + 3 A = 3.02 A Maximum supply current for Power block = 3.1 A Result 3.02 A 3.1 A OK -23No.EX-OMH0025-C Calculation example for supply current (3)Power block Output block for high wattage load The maximum
be read. (1) (3) (2) -23No.EX-OMY0032-B 8.6.2.
After the input of the first 3 digits is complete, press the 3 digits Press the button again. button for 1 second or longer. The flashing will stop. Press the button again to confirm the values of the first 3 digits and move onto the input of the next 6 digits.
To enable the QuickConnectTM function, it is necessary to perform the settings 1 to 3 to the SI units shown below. After satisfying the conditions 1 to 3, setting of the QuickConnectTM function compliant EtherNet/IPTM module (master), according to the specified procedure, must be performed.
Power cable 1 Brown Power supply Vcc 2 White NC 3 Blue GND 4 Black Monitor output Signal cable 1 Brown Input signal 1 2 White Input signal 2 3 Blue Input signal 3 4 Black Input signal 4 5 Gray Common Common is no polarity.
Input data only (Default setting) Pin number OFF OFF OFF ON ON ON 2 : : 3 1 4 2 Content Content 100 Mbps, half duplex 100 Mbps, full duplex 10 Mbps, half duplex 10 Mbps, full duplex OFF OFF OFF ON ON ON 3 : : Automatic Signal name Setting2 1 2 3 4 5 6 7 8 ON OFF OFF OFF ON ON ON RX+ RXSettings2 TX+ TX: : OFF OFF OFF ON ON ON : : (2) (3) Content OFF OFF OFF ON ON ON SI unit output data size
Body Size: 30 (4000 L/min), Pressure Range: 30 (0.005 ~0.5Mpa), Fieldbus: SPN (PROFINET), Thread: N (NPT), Port: 4 (1/2", 3000)
Body Size & Pressure Range: Body Size: 4000 L/min; Pressure Range: 0.005~0.5Mpa, Protocol: PROFINET, Thread: NPT, Port: 4 [1/2, (3000)], Made to Order: -
Thread: F (NPTF), Port: 3 [3/8" (2000, 3000)], Stations: 7 Stations, Pressure: 2050 (0.9 MPa), Protocol: SEN (Ethernet I/Pâ„¢)
Thread: N (NPT), Port: 3 [3/8" (2000, 3000)], Stations: 2 Stations, Pressure: 2050 (0.9 MPa), Protocol: SEN (Ethernet I/Pâ„¢)
Thread: F (NPTF), Port: 3 [3/8" (2000, 3000)], Stations: 5 Stations, Pressure: 2010 (0.1 MPa), Protocol: SEN (Ethernet I/Pâ„¢)
Thread: F (NPTF), Port: 3 [3/8" (2000, 3000)], Stations: 2 Stations, Pressure: 2030 (0.5 MPa), Protocol: SEN (Ethernet I/Pâ„¢)
Thread: F (NPTF), Port: 3 [3/8" (2000, 3000)], Stations: 5 Stations, Pressure: 2030 (0.5 MPa), Protocol: SEN (Ethernet I/Pâ„¢)