SMC Corporation of America
Elite Part Number Search
Search Results "IN-777-160TF-300F-HL"

Stroke adjustment unit appearance and mounting direction In case of the MY3B L unit Right H unit Port Left Stroke adjustment unit Installation example HL Port Applicable Auto Switches/ Refer to Best Pneumatics No. 2, pages 1263 to 1371 for further information on auto switches.

OUT IN OUT IN OUT IN OUT IN OUT IN 56 31 157 100 353 252 628 471 982 756 1608 1206 4 CXS 6 15.7 10.0 35.3 25.2 62.8 47.1 98.2 75.6 161 121 6 CXS10 8 CXS15 Manual Release 10 CXS20 Manual release (Non-locking type) 1.

OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT 12 16 20 25 32 40 50 63 80 100 125 140 160 180 200 1N = 0.2248 lbf 6 Double Acting, Single Rod Technical Information Standard, and with Non-Rotating Rod Series (N)CQ2(K) Weight Standard High Lateral Load Standard Single Acting Double Rod Axial Piping Water Resistant End Lock Clean Series

In such a case, use a side support in the middle section. The spacing (l) of the support must be no more than the values shown in the graph on the right.

In this case, the rigidity of the machinery should also be examined. 5. Consider a possible drop in circuit pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.

Remove the covers as shown in Figure (2) and make further adjustment by loosening the hexagon nut. 3. Various dimensions are indicated in Table (1). Never make an adjustment that exceeds the dimensions in the table, as it may cause an accident and/or damage.

is installed in the MGPM20-50AZ.

In this case, the rigidity of the machinery should also be examined. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.

In this case, the rigidity of the machinery should also be examined. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.

In this case, the rigidity of the machinery should also be examined. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.

to 100 5 to 395 Part no.: MGPA20-39 A spacer 1 mm in width is installed in a MGPA20-40.

Furthermore, when subjected to impact in use as a stopper, etc., screw the mounting bolts in to a depth of 2d or more. Plate pin hole position accuracy When the cylinder is mounted, disparities in the machining dimensions of each part are accumulated in the plate pin hole accuracy. Use the values below for reference. L [Side mount] Pin hole 2d or more (d = thread O.D.)

In this case, the rigidity of the machinery should also be examined. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.

The allowable load mass and maximum operating pressure should be as shown in the table below. The cushion effect (smooth start-up, soft stop) exists only before the stroke end in the stroke ranges indicated in the table below. The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc.