4/5 Port Solenoid Valve Rubber Seal Series SYJ3000 For details about certified products conforming to international standards, visit us at www.smcworld.com. Non-standard strokes for a size 6 cylinder are available as a special order.
As some parts of the air dryer will remain hot, there is a risk of burns due to residual heat after the power is switched off. So do not carry out replacement work until the temperature of these parts has fallen to 50 or less. Wait for about 10 to 15 minutes as a guide.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
-Pad ;;rol2 25 40 Flat type I a o o o a o a o o a o o Flat with rblo o a o o a a o eep tvpe lo a o a Bellows | a a a a a a o a a a 132 ZCDUKC Male Cap porting zPf (v&uum pad !
-Pad ;;rol2 25 40 Flat type I a o o o a o a o o a o o Flat with rblo o a o o a a o eep tvpe lo a o a Bellows | a a a a a a o a a a 132 I ZCDUKC Male Cap porting zPf (v&uum pad !
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder.
15 54.5 24.5 80 24.5 (mm) Stroke adjustable range Retracting 5 15 25 35 30 15 35 35 35 A dimension (Retracted side mounting) Extending Model Shock absorber at retraction end MXS25-10 MXS25-20 MXS25-30 MXS25-40 MXS25-50 MXS25-75 MXS25-100 MXS25-125 MXS25-150 26 36 46 46 43 27 48 46 46 Stroke 100 to 150 A Shock absorber at extension end Max. 35 Shock absorber at retraction end Dimensions not
Option Note ZS-28-CA-4 Sensor connector For PF3A7H ZS-46-A1 Bracket A Tapping screw: Nominal size 3 x 8 L (2 pcs.) ZS-46-A2 Bracket B Tapping screw: Nominal size 3 x 8 L (2 pcs.)
Keep wiring as short as possible.
In that case, insert a noise filter such as a line noise filter/ferrite between the switching power supplies or change the switching power supply to the series power supply.
Use the table as a guideline for mounting.
Type 46 Type S46 Single solenoid coil is located on same side as the A, B port.
backflow mechanism as a standard feature.
Bore size (mm) Auto switch mounting surface 20, 25 63, 80, 100 32, 40, 50 Port side Port side Port side C A C A C A B B B Auto switch mounting surface Auto switch mounting surface Auto switch mounting surface Auto switch model A, B, C sides Port side Port, A, B, C sides Port, A, B, C sides 1. BQ-2 2. BQ2-012 Two kinds of auto switch mounting brackets are used as a set.
The proper tightening torque for pipe fittings is as shown in the table. As a rule, they should be tightened 2 to 3 turns with a tool after first tightening by hand. Be careful not to cause damage by over-tightening. Caution 1. The product cannot be used as a stop valve, of which zero leakage is required. The specifications of the product allow a certain degree of leakage. 2.
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder. 4.
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder. 4.
As a reference, the tightening torque is 1 to 1.5 Nm. (When replacing the piping adapter ZS-46-N# tighten it using the same method.) Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm.
Extend the dimensions of A, H. when using a single/double knuckle joint together with a rod end nut. (To extend dimensions A/H, refer to the table below, and specify the product as Made-to-order -XAO.)