SMC Pneumatic Clean Series When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
During Auto tuning Auto tuning failure A T 1 E R R 1 9 P V < 2 3 . 0 C # 1 A T F a i l u r e A u t o T u n i n g M O D E S h u t O f f C a n c e l : A T k e y <4> External sensor sampling cycle setting: Mode indication External Sensor Sampling Cycle. Default value: 180 sec. Setting range 10 to 999 sec.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
In an environment where the product will come into direct contact with rain, wind and snow or with a lot of moisture (relative humidity 85% or more). (Note) In a location with a large quantity of dust. In a location containing flammable or explosive gases. In a location exposed to corrosive or flammable gases or solvent.
Clip Type 45 manifold permits change in the A and B port sizes by changing the manifold block fitting assembly. After removing the valve, remove the clip with a screwdriver. To mount a new fitting assembly insert it and then insert a clip so it does not come out of the manifold block. Loosen bolt (a) fixing the manifold base until it begins to turn idly.
From a point indicating 500 mm/s on the axis of abscissas, extend a line upward and find a point where it intersects with a line for the 63 mm bore size. Extend a line from the intersection to the left and find a load mass 80 kg.
Ventilation Provide ventilation when using a valve in a confined area, such as in a closed control panel.
Clip Type 45 manifold permits change in the A and B port sizes by changing the manifold block fitting assembly. After removing the valve, remove the clip with a screwdriver. To mount a new fitting assembly insert it and then insert a clip so it does not come out of the manifold block. Loosen bolt (a) fixing the manifold base until it begins to turn idly.
In an environment where the product will come into direct contact with rain, wind and snow or with a lot of moisture (relative humidity 85% or more). (Note) The option B is provided for installation under a roof, but should not be used in environments where rain or snow may fall on it. In a location with a large quantity of dust. In a location containing flammable or explosive gases.
Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure In the OUT2 setting, the above P_1, n_1 and H_1 will be P_2, n_2 and H_2 respectively.
Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure In the OUT2 setting, the above P_1, n_1 and H_1 will be P_2, n_2 and H_2 respectively.
Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure In the OUT2 setting, the above P_1, n_1 and H_1 will be P_2, n_2 and H_2 respectively.
M5 ground screw 9 9 2n-Rc 1/2 4(A), 2(B) port VQ0 U side 34.5 VQ4 n X 12 X 12 VQ5 B 2 A 4 6 B B B B B B A A A A A A VQZ B 2 A 4 VQD 5 SMC SMC SMC SMC SMC B 2 A 4 4 L1 L2 B 2 A 4 3 B 2 A 4 2 P = 41 P = 41 B 2 A 4 1 Cable length (600 or 1500 mm) 58.5 34.5 48 68.5 Stations D side 42 16 15.5 61.8 133 22 51 69 117 2-Rc 1/8 (External pilot port) Dimensions Formula: L1 = 41n + 76, L2 = 41n + 96
Note) If T slots on the bottom in used for installation, select screw which enables only Installation of actuator (Using the mounting holes from the top) A A Model Bolt Max. tightening [mm] torque [Nm] [mm] LEMB M5 3.0 5.5 24.5 LEMC25 LEMH25 M3 0.63 3.4 23.7 LEMC32 LEMH32 M5 3.0 5.5 30.1 LEMHT25 M5 3.0 5.5 21.6 LEMHT32 M8 12.5 9 26.9 Installation of actuator (Using the nuts from the bottom
MPa. 01 1/8 male thread, M5 female thread M5 x 0.8 OUT IN OUT Thread type Nil N Rc NPT OUT IN OUT Note 1) Use caution not to tighten excessively when mountinga pressure gauge, otherwise it may result in a breakdown.
MPa. 01 1/8 male thread, M5 female thread M5 x 0.8 OUT IN OUT Thread type Nil N Rc NPT OUT IN OUT Note 1) Use caution not to tighten excessively when mountinga pressure gauge, otherwise it may result in a breakdown.
Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure If setting is not necessary press the and buttons simultaneously for 1 second or longer. -34No.PS-OMS0007-H [F 6] Fine adjustment of display value This function is to manually perform a fine adjustment of the displayed pressure value.