ISE70/75/75H Do not attempt to rotate the connector, as it is not rotatable.
Do not use until you can verify that equipment can operate properly. Verify correct mounting by suitable function and leakage inspections after air and power are connected following mounting, maintenance or conversions. 2. Do not drop or bump. Do not drop, bump or apply excessive impact (1000 m/s2) when handling.
Do not scratch or gouge the sliding part of the piston rod or guide rod. This will cause air leakage or malfunction due to damage of the seals. 2.
Do not connect. Do not connect. Connect to actuator power line (Yellow) Connect to actuator power line (Red) Connect to actuator power line (Blue) Connect to actuator power line (Orange) Connect to actuator power line (Black) Connect to actuator power line (White) When an alarm occurs, this signal turns off the alarm after the cause is resolved.
Prevention of electric shock and fire Do not operate the switch with wet hands. Also, do not operate the Thermo-con with water left on it. 2. Action in the case of error If any error such as abnormal sounds, smoke, or bad smell occurs, cut off the power at once, and stop supplying and conveying fluid. Please contact SMC or a sales distributor to repair the Thermo-con. 3.
Do not use this product with a fluid other than compressed air (e.g. oxygen, hydrogen, inflammable gas, mixed gas, etc.). -Do not use compressed air which includes chemicals, organic solvents, or corrosive gases, etc. It may lead to damage or malfunction. Do not use for caisson shield, breathing, medical purposes, air blow to any medicines and foods that enter the human body.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not expose the product to direct sunlight for an extended period of time. 3. Do not use in a place subject to heavy vibration and/or shock. 4. Do not mount the product in locations where it is exposed to radiant heat. Warning 3.
Example Warning Mounting 0.1 0.2 0.3 Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. 2. Insert the cable through the conduit and install the wires according to the terminal board layout below. Manifold expansion 0.4 0 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. Air Supply 1. Type of fluids Please consult with SMC when using the product in applications other than compressed air. 3. Do not use in a place subject to heavy vibration and/or shock. Warning 4.
Do not apply an excessive force to the finger guard. If an excessive external force is applied to the finger guard (including the filter holder) on the air suction side of the product, it may be broken. Do not apply an external force of 50 N or more to the finger guard. Caution 1. Clean specification is not available with this product.
Do not use the compression fitting of the valve to support the piping. The piping could disconnect from the valve. Be sure to mount the valve to secured piping. (Compression fittings do not have a valve-holding function.) Caution 1. Use a steel tube for the IN and OUT piping. 2.
Operating Environment Maintenance Caution Warning 1.Do not use in atmospheres where the valve is in direct contact with corrosive gases, chemicals, salt water, water or steam. 2.Do not use in locations subject to vibration or impact.
Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 6.
Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water vapor, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Do not use until you can verify that equipment can operate properly. Verify correct mounting by suitable function and leakage inspections after air and power are connected following mounting, maintenance or conversions. 2. Do not drop or bump. Do not drop, bump or apply excessive impact (1000 m/s2) when handling.
Do not operate or set with wet hands. This may lead to an electric shock. End plate bracket (EX600-ZMA2) SUPPLIERS DECLARATION OF CONFORMITY Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Connector (Base only) (2) Add more units.
Do not use with flammable or highly permeable fluids. Fire, explosion, damage or corrosion can result.
Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. UP button Selects a mode and the display shown at the sub screen, and increases the ON/OFF set values.
Do not apply fluid under leaking conditions. Safety cannot be assured in the case of unexpected malfunction.
Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. 5% of rated flow Hysteresis Setting of hysteresis can prevent chattering. UP button Selects a mode and the display shown at the sub screen, and increases the ON/OFF set values.