Compact Cylinder/Standard Type: Double Acting, Single Rod Basic style Rod seal Piston seal NBR CQSB12-PS CQSB16-PS CQSB20-PS CQSB25-PS 12 16 20 25 CQSB12-PS CQSB16-PS CQSB20-PS CQSB25-PS Tube gasket Long stroke CQSB12-L-PS CQSB16-L-PS 12 16 20 25 CQSB12-L-PS CQSB16-L-PS CQSB20-L-PS CQSB25-L-PS Set of left nos. !5, !6, !7. CQSB25-L-PS CQSB20-L-PS Seal kit includes !5, !6, !7. Order the seal kit, based on each bore size.
VQZ100 ( ( ( ( ) ) ) ) 90 VQZ200/300/1000/2000/3000 VQZ200/300/1000/2000/3000 VQZ200/300/1000/2000/3000 VQZ200/300/1000/2000/3000 DC L,M L,M L,M L,M
/2(A): Male thread 1(P): Male thread/2(A): Male thread 1(P): Male thread/2(A): One-touch Applicable tube O.D.
fitting 1(P): Male thread 2(A): One-touch fitting 1(P): One-touch fitting 2(A): Male thread 1(P): Male thread 2(A): Male thread 2(A) 2(A) 2(A) 2(A) Applicable tubing O.D.
Characteristics JIS B 8372 (In accordance with air regulator) SRF 1(P) 2(A) 3(R) VCHR (Inlet pressure) (Outlet pressure) Set point ITV IC ITVX PVQ Inlet pressure (MPa) VEF VEP VEF VEP 3(R) 2(A) Flow rate (L/min (ANR)) 1(P) 2(A) Inlet pressure: 0.3 MPa VER Set point VEA VY1 VBA VBAT Inlet pressure (MPa) AP100 Set point 3(R) 2(A) Flow rate (L/min (ANR)) 1(P) 2(A) Inlet pressure (MPa) 889
Caution VM VR Mounting Caution VH L type bracket mounting: Apply a tightening torque of 0.5 to 0.6 Nm to the bolts when the bracket is mounted on the body. VHS Flame Resistant Type: 1(P)/2(A): One-touch Fitting Applicable tubing O. D.
Take safety measures (e.g. mounting protective covers) when there is a danger of fingers being caught in a gripper or workpieces causing damage, etc. 3. There is a danger of workpieces dropping if there is a decrease in gripping force due to a drop in circuit pressure caused by a power failure or trouble with the air source.
When used without a guide for a light load. When space is very limited. Series REAS Size: 10, 15, 20, 25, 32, 40 Smooth operation is possible through the use of a special slide bearing. To ensure a permanent path. When used for general transporting. A load can be carried directly by the integrated guide type.
To connect a drain discharge pipe, use a pipe with a minimum bore of 10, and a maximum length of 5 m. Avoid using a riser pipe.
Tightening of M3/M5 Threads 1) Tighten a barb fitting by hand, and give it an additional 1/6 turn with a wrench. 2) Tighten a barb elbow by hand, and give it an additional 1/3 turn with a wrench.
103 103 38 38 19 19 65 65 150.5 150.5 SIZE 1 SIZE 1 SIZE 2 SIZE 2 SIZE 3 SIZE 3 205 205 228 228 110.5 110.5 25 25 32 32 50 50 64 64 67.5 67.5 175 175 198 198 122 122 71 71 10 Series VS R8 Rubber Seal S ISO SIZE 1 SUB-BASE VS8-1-w 02/03/04w 2-1/4,3/8, 1/2 A,B PORTS L L 2-1/8 PILOT EXH PORTS 15 33.5 A A B B 29.5 29.5 5-1/4 PORTS M12 CONNECTOR (OPTIONAL) 2-7 MOUNTING HOLES 43.5 23 23 11.5 14
In the case of bore size 6, be sure to attach a plate on Cylinder A (on the surface opposite to the switch groove). With Shielding Plate Bore (mm) 6 8 10 L d 16 3 13.5 0.5 14 0.5 7-2-13 13 Series CUJ Specific Product Precautions 1 Be sure to read before handling. Mounting Selection Caution Strictly observe the limiting range of lateral load on a piston rod. (Refer to the graphs below.)
for attaching a limit switch Applicable product Kit no.
2) A(2) AQ Weight (g) (g) Model Min.
4 60 PSI (4kg|/cm') 6 90 PSI (6kglicm") lnput Current 0-4-20mADC(standard) . l 1 5 m A D C ' 2 2 1 0 m A D C ' 3 5 2 5 m A D C *4 10 50 mADC ' Special Order o ,,' Ogeration'/ Construction Model MmOO(Lever type) Single acting, Normal operation When the input current increass, the armature witt be subjected to a clockwise torque, pushing the flapper lever to the teft.
Turn cover A counterclockwise until it stops (approx. 45). 4. Install a new element on cover A and insert it into the case. Cover A Case Cover A Case O L L Element O-ring Window 5.
When installing a paddle on IF3O type, piping may be interfered with by the tip of a paddle. Because this is used to detect a small flow rate, and to narrow the distance between a paddle and piping, additional machining of the paddle tip may be necessary to eliminate interference between the two. 6. Use pipe fittings that comply with JIS specifications.
Please consult with SMC for the supply of a pressure gauge with NPT port threads. Note 2) Use caution not to tighten excessively when mounting a pressure gauge, otherwise it will may result in a breakdown. For sealing, use a sealant tape. Flow rate (L/min (ANR)) ARP IR-A Option/Mounting Bolt Assembly IR Model Part no. Dimensions Qty.