CJ2-Z 10-/11- Series 21-/22- Air Cylinder/ø10, ø16 Auto Switch Proper Mounting Position (mm) Auto switch model D-M9 D-M9W D-A9 A A B B Bore size 10 16 (5) 6 (5) 6 (1) 2 (1) 2 (5.5) 6.5 (5.5) 6.5 (1.5) 2.5 (1.5) 2.5 The values in ( ) are measured from the end of the auto switch mounting bracket. Note) The above-mentioned value is a guide for auto switch mounting position for stroke enddetection.
6 !7 !8 !9 @0 @1 @2 @3 @4 @5 No.
6, !7, !9 !5 !6 !7 !8 !9 6, 10: Not available Wear ring A Special resin CY3B6-PS 6 CY3B6-PS Wear ring B Special resin Set of left nos. !6, !7, !8, !
If it is used in an environment where there is possible contact with oil, weld spatter, etc., exercise preventive measures. 6. 7.
Step 6 3 Bolt b Tightening torque of bolt a Nm Tightening torque of bolt b Nm 1 2 Valve size Tightening torque Valve Tightening All sizes 0.3 size torque 4 XLA-16 0.7 -25 1.5 -40 2.5 -50 6 Bonnet assembly -63 6 -80 15 -100 20 Heater -160 102 Pilot port Bolt a Cover Body Apply 0.4MPa of air pressure to the pilot port.
AF AR 4 - 1) 5 2) 3) 5 4) 1 ISO VG-32 2-2. 1) 2) 3) 4) 5) 6 7) 5 - 8 9) , 10) 11) 3 1) P10 [2-6.] 2) 3) 4) 5) 6) 7) (40) 6 - 2-3. 1) 1 P10 [2-6.] fR Ft N () mm 1. (MPa)=(MPa)+{(kg) 2)} X /(mm ,, 2) 3) 4) 7 - 5) 6) 7) 8) 9) 24. 1) 2) 3) 8 - 1) 2) 1.52 2 2. 2-5. ,AS 9 - 2-6. P7.1. 1.
L 100mm, or stroke 1 2 1 7 5 4 6 2 6 5 7 3 L L Fig. 9 Position for application of grease Table 10 Amount of grease units: g Stroke 40 50 63 80 100 P o s i t i o n f o r Bore g r e a s e At 100st 3 to 4 3 to 5 4 to 5 6 to 8 8 to 10 50st added 1 1 1.5 2 3 20 3-2-4. Mounting of seals 1) Rod seal, Cushion seal (Fig.9, ) Pay attention to the mounting direction of the seal.
Product Specifications . 6 3-1. How to order . 6 3-2. Specifications . 6 3-3. Auto switch . 7 3-4. Gripping force . 8 3-5. Gripping point . 9 3-6. Dimensions . 10 3-7. Air Gripper Single Unit .11 3-8. Center of gravity . 12 4. Product Specifications . 13 4-1. Attachment . 13 4-2. Protection cover . 14 4-3. Mounting to duAro flange . 15 4-4.
No.MH*-OMZ0004 / / JMHZ2-16D-X7400B-ASSISTA(-P) . 2 1. 4 2. . 5 3. . 6 3-1. . 6 3-2. . 7 3-3. . 8 3-4. () . 9 3-5. . 10 3-6. . 10 4. . 11 4-1. . 11 4-2. 3 . 12 4-3. . 13 5. . 14 5-1 . 14 5-2. . 14 5-3. . 20 5-4. . 20 5-5. . 20 5-6. . 21 6. . 21 1 - (ISO/IEC)(JIS)*1) *2) *1) ISO 4414: Pneumatic fluid power -General rules relating to systems ISO 4413: Hydraulic fluid power
Product Specifications . 6 3-1. How to order . 6 3-2. Specifications . 6 3-3. Auto switch . 7 3-4. Gripping force . 8 3-5. Gripping point . 9 3-6. Dimensions . 10 3-7. Air Gripper . 11 3-8. Center of gravity . 12 4. Product Specifications . 13 4-1. Attachment . 13 4-3. Mounting to NEXTAGE . 15 4-4. Piping . 16 4-5. Speed controller . 16 4-6.
*Refer to "1-6 Accesories" for belonging parts of each bracket. 27 - .
Auto switch mounting tool When tightening the auto switch mounting screw (included with the auto switch), use a screwdriver with a handle diameter of about 5 to 6 mm.
Step 6 3 Bolt b 1 Tightening torque of bolt b Nm Valve size Tightening torque Tightening torque of bolt a Nm Tightening torque of bolt a Nm 2 4 Valve size Tightening torque Valve size Tightening torque All sizes 0.3 All sizes 0.3 XLF-16 0.7 -25 1.5 -40 2.5 -50 6 Bonnet assembly -63 6 -80 15 -100 20 Bolt a Heater Pilot port -160 102 Cover Body Apply 0.4MPa of air pressure to the pilot port
ring 6 Note2) The material of the O ring for sliding of S valve is FKM.
This may reduce the lubrication performance and shorten the life of the equipment. 6. Avoid using the product in an environment that exposed to foreign matter.
The disassembly of them may deprive holding force from the magnet and cause operating failure. 6-4) Take off the watch for handling of external slider and piston slider. 6-5) Handle external slider and piston slider with care to protect the magnet from drop on the floor and collision to the metal. And apply the grease periodically on external face of cylinder tube.