When reassembling, do the opposite. Type 01T Wth Terminal Block Wirins . Remo\ junction cover of manifold to expose terminal block attached to the manilold block. Lead wires from solenoid valve are connected with the terminals on the upper side of the terminal block.
stations exhausl hom bolh sides of manllold. 20 20 stations BLnk pHl.3dy DXT20I -r 5-14 NW3Z5-2!Ol NW3Z5-21R{)l Applkrbl. valvo6 . NW3Zs-21-O1-007 Nvzsl2-OOO-o1T NVz5i2M-OOO-017 . NW3Z5-21R-O1-007 NVzslzR-elCO 01T NW3 ott, statpns t 20 20 stations ll there are more than I stations, supdy air and exhaust from trcth sides of manifold.
flow rate: l/min Accumulated flow: l, m3, m3 x 103 Port size Output specification Port size Applicable model Flow rate (l/min) 28 29 68 69 NPN open collector 1 output + Analog output (1 to 5 V) NPN open collector 1 output + Analog output (4 to 20 mA) PNP open collector 1 output + Analog output (1 to 5 V) PNP open collector 1 output + Analog output (4 to 20 mA) Symbol 3000 6000 12000 10 14
Do not connect the white wire of the sensor to c of the display unit. View A Terminal block number 4 3 2 1 1 2 3 4 5 6 7 8 8 7 6 5 Series PF2D For Deionized Water and Chemicals Digital Flow Switch Functions/PF2D Refer to the operation manual how to set and to operate. Output types Flow rate measurement selection Real-time flow rate and accumulated flow rate can be selected.
Reconfiguring the operation mode, as well as the zero and span adjustments, are easy to do in the field. INSTALLATION B D Installation Transmission Din & Feed-back lever Fig. SINGLE-ACTING ACTUATOR SIGNAL PRE-Y%i-rpur SIGNAL RANGE INSTALLATION STYLE IREF. FIG. 1) OUT 1 OUT2 Direct ?
Internal voltage drop in switch is 4V. 8 Series MGF Contact Protection Boxes/CD-P11, CD-P12 Auto Switches Proper Mounting Position for Stroke End Detection D-Z7 and D-Z8 type switches do not have builtin contact protection circuits. A contact protection box should be used in any of the following cases. B A 1. The operated load is an induction load. 2.
Do not use in locations where there is splashing or spraying of oils and solvents. OUT2 OUT1 3. When using a commercially available switching regulator, be sure to ground the FG terminal. SET 4. In locations where the switch is exposed to water and dust, etc., these may enter the switch from the atmospheric release port.
Do not touch heated areas (tubing, heat gun). Also, be careful not to touch the other side of the heated area since the temperature also increases there due to hot air. After heating up the end of the tubing, immediately slide it over the insert pin up to the base of the insert, thereby expanding the tubing into a flared shape.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.
SP157X-014E P TY P.G.Information (Specialized Product ) Step motor (Servo 24 DC) Absolute Controller LECP7-XB3 Series SMC Corporation 4-14-1, SOTO-KANDA, CHIYODA-KU, 101-0021, JAPAN URL: http://www.smcworld.com Return to origin not required after power is OFF/Shorten equipment recovery time The current actuator position can be monitored even if the power of the battery is shutoff The position
Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN URL http://www.smcworld.com 2010 SMC Corporation All Rights Reserved 09-E548 D-DN Vinyl Chloride Air Operated Valve Series LVP Piping from 4 directions are possible.
When washing the element, do not wipe it using a stiff brush or rag.
When this is done, take care that the coverings of the lead wires do not enter the core wire crimping area. Use special tool when crimping. (For the crimping tool, please consult with SMC.)
Do not use the regulator with flow exceeding the Max. flow indicated in Flow Rate Characteristics as this can cause failure in pressure adjustment. Bleed port Component Parts Knob locking screw No.
Insert the cover nail into hole of case (\l mark), set the mark( DO ) of the cover to the case and rotate the cover ctockwise until it stops.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened. As a result, it might not be possible to connect the tubing, or after the tube has been connected, it could pull out or allow air to leak.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Series: 2 (VQ20), Stations: 15 Stations, Option: D (DIN Rail Mounting), Thread: 00T (NPTF3/8)