LZ-OM003xx Warning 6. Test run (2)Test run details gradually. 5. Wiring
Outline.6 3. How to Order.7 4. Specification.7 5. Mounting .7 5-1. Electrostatic sensor installation.7 5-1-1. Sensor head installation.7 5-1-2. Installation of the sensor amplifier.8 5-2. Circuitry and wiring chart.9 6. Performance.10 6-1. Output signal.10 6-2. Detection range.11 6-3. Cautions on installation .11 6-4. Timing chart .12 7. Exterior dimensions.12 1 1.
Product Specifications .6 3-1. How to order .6 3-2. Specifications .7 3-3. Gripping force .8 3-4. Dimensions .10 3-5. Connector and pin layout . 11 3-6. Center of gravity .12 4.Product Specifications .13 4-1.Magnet Gripper .13 4-2. 3-port solenoid valve .14 4-3. Auto switch .15 5.Operating method or operation .16 5-1Precautions for Design .16 5-2. Installation .17 5-3.
A B A B DIN terminal: VP3165-D Conduit terminal: VP3165-T Conduit terminal with indicator light (TL) Light Light G 1/2 Max. 11 Applicable cable 6 to 12 G 1/2 Rc 1/4 ( ): With indicator light (TL) 4-10-6 7 Large Size 3 Port Solenoid Valve Rubber Seal Series VP3145/3165/3185 Dimensions: VP3185 A B Grommet: VP3185-G V100 G 1/2 SY SYJ Manual override Lead wire length 200 mm External pilot
Doc.No.MH*-OMY0017-A PRODUCT NAME Magnet Gripper Unit for Collaborative Robots MODEL / Series / Product Number MHM-25D-X7400A-TM Contents Safety Instructions .2 1.List of included items .4 2.Parts description of the magnet gripper .5 3.Product Specifications .6 3-1. How to order .6 3-2. Specifications .7 3-3. Gripping force .8 3-4. Dimensions .10 3-5. Connector and pin layout . 11 3-6.
For manifold type 30, 31 Large flow type (Cv: 0.012) 1 SY1 3 A 5 L M3 : Body ported Large flow type (Cv: 0.012) 5 SY1 4 A M 1 : Base mounted 3 port Rated voltage Port size 5 6 V S R 24 VDC 12 VDC 6 VDC 5 VDC 3 VDC Nil: Without sub-plate M3: With sub-plate Sub-plate type For manifold type S41 Large flow type (With gasket and screws) Electrical entry Manual override 24 V, 12 V, 6 V, 5 V, 3
Product Specifications .6 3-1.How to order .6 3-2. Specifications .7 3-3.Gripping force .8 3-4. Dimensions .10 3-5. Connector and pin layout . 11 3-6. Centor of gravity .12 4. Product Specifications .13 4-1. Magnet gripper .13 4-2. 3-port solenoid valve .14 4-3. Auto switch .15 5.Operating method or operation .16 5-1Precautions for Design .16 5-2. Installation .17 5-3.
Description Material 1 Body ADC 8 Seal NBR 2 Main valve Resin 9 Washer Fe (Chromated) 3 O-ring NBR 10 Compression nut ADC 4 Bonnet ADC 11 Hexagon bolt Stainless steel 5 Sub-valve Resin 6 O-ring NBR 7 Bonnet ADC JSXFAF/Direct Piping Type Port size: Sizes 06, 10 Port size: Size 14 i u y t t r r e e w IN w IN q q Component Parts Component Parts No.
(Refer to Figure 1.) 4) Remove the cable gland (4) and plain washer (5) and rubber seal (6). 3. Wiring 1) Passing through the cable (7), cable gland (4), plain washer (5), rubber seal (6) in this order, and then insert into the housing (2). 2) From the terminal block (3), loosen the screw (11), then pass the lead wire (10) through, then again tighten the screw (11).
Class Symbol PAF341S 12 x 10 10 x 8 19 x 16 12 x 10 25 x 22 19 x 16 PAF541S PAF341S PAF541S tubing size (mm) tubing size (inch ) SMC SMC SMC 4 4 5 5 6 6 1 2 1 2 1 2 4 4 5 5 6 6 A B A B A B 1/2" x 3/8" 3/8" x 1/4" Panel mount union U P 3/4" x 5/8" Union 1/2" x 3/8" 1" x 7/8" 3/4" x 5/8" SMC Note) Select the fitting after confirming the IN / OUT side fitting size and fitting type.
VXF*-OML0001-A PRODUCT NAME Valve Controller MODEL / Series / Product Number VXFC06D VXFC10D VXFC06D-6 VXFC10D-6 Contents 1. Safety Instructions P2-5 2. Specifications P6 3. Name of Parts P7-8 4. Wiring P9 5. Description of operation P10-11 6. Cascade connection P12-13 7.
Do not fully close the cushion valve. 6.If the cushion valve is opened too much, the cylinder will operate like cylinders without an air cushion, and the impact force will be extremely large. 7.Air cushion is not for reducing the piston speed around the stroke end. 13 2-6-3.
Contact SMC for cantilever mounting as shown in Fig. 6. Deflection of the cylinder body may result in operation failure. Fig. 5: Product mounting with the slide table fixed Fig. 6: Cantilever mounting Prohibited Consult SMC The cylinder tube may deflect due to its own weight, load, or etc.
Wireless log data files Wireless log data is generated and stored in the following four csv files. -94No.EX##-OMV0017-D 6.
24. 1) 2) 3) 1) 2) 1.5~2 2 2. 2-5. ,AS 8 2-6. 2-6-1.
Ground 4-7-11 12 Series VT317 How to Use DIN Terminal 1.
HRSH 090 HRSH 090 6 Signal for the completion of preparation A signal is output when the circulating fluid temperature reaches the set temperature, when using contact input/output and serial communication. !0 !1 !2 !3 !4 !5 !6 HRSH No.