2-Color Display Digital Pressure Switch Series ZSE80(F)/ISE80(H) Do not exceed the screw-in torque of 13.6 Nm when connecting the pipe to the switch. Exceeding these values may cause the switch to malfunction. 4. Do not use pressure sensors with corrosive and/or flammable gases or liquids. 3. Some fluids may generate static electricity when resin piping is used for piping.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in locations influenced by vibrations or impacts. 3. This vacuum regulator always uses atmospheric air, therefore, do not use in dusty environments. 4.
Do not synchronize multiple cylinders. Do not operate two or more end lock cylinders synchronized to move a single workpiece because one of the cylinder locks may not be able to disengage when required. 6. Operate the speed controller under meterout control. If operated under meter-in control, the lock might not disengage. 7.
Do not rotate the screw more than 30 degrees for additional tightening. (The maximum tightening torque: 0.2 Nm) 3. Do not mount the product in a place where dust will be stirred up by the exhaust air from the product and affect peripheral equipment. 4. Do not mount the product in a location where air from the product will be directly exhausted to the workpiece. 5.
Time Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. 3 Step Setting Mode Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Time Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. 3 Step Setting Mode Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Switch ON At normal output Switch OFF Safety Instructions Time Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Maintenance 3 Step Setting Mode Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
When tightening, do not hold the pressure switch body with a spanner. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
When tightening, do not hold the pressure switch body with a spanner. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
When and buttons are pressed and held simultaneously for 1 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
An injury or failure can result. 3 Step Setting Mode Maintenance Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
SET for 2 s or longer Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. 1. 1) OUT1 operation mode setting SET 1. 2) OUT1 output mode setting Troubleshooting Do not operate in an atmosphere containing flammable or explosive gases.
The output OUT1(1) set value input mode is selected. 1: The set value of P1 is -50 Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not use pressure sensors with corrosive and/or flammable gases. 7. The applicable fluids are air, non-corrosive gas and non-flammable gas. Consult with SMC if the switch is to be used with other types of fluids. Caution Connection Caution 1. Do not drop, bump, or apply excessive impacts (100 m/s2) while handling.
Connection Be sure that chips from the pipe threads and sealing material do not get inside the piping. Further, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of male threads. Do not use with gases. 4.
Do not attempt to rotate the connector, as it is not rotatable.
HRR Series 3.1 Precautions wiring communication 3-1 HRX-OM-W004 Chapter 3 Serial communication 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
Do not hit the table with the workpiece in the positioning operation and positioning range. 11. When mounting the product, use screws with adequate length and tighten them with adequate torque.
Do not use in a location having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources. Maintenance Warning 1. Maintenance should be performed in accordance with the procedures in the Operation Manual.