c Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. Caution 3. In locations near heat sources, block off radiant heat. 1. Check the model number, size, etc. before installing. The TLM and TILM series do not have the model number displayed on the product due to the resin material used.
Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions.
Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 4.
Regulator and filter regulator 1) Be sure to unlock the handle before adjusting the pressure and to lock it after the pressure is set. 2) During transport and installation, do not apply shock to the product, such as by dropping doing so will affect its precision. 3) Do not install it iin an area that is exposed to high temperature or humidity, because doing so will lead to improper operation
Note) The dedicated software (LEC-BCW) is required. * When controller equipped type is selected when ordering the LE series, you do not need to order this driver. * When pulse signals are open collector, order the current limiting resistor (LEC-PA-R-m) separately. The driver is sold as single unit after the compatible actuator is set.
Do not operate exceeding the operating pressure range. 2. Do not operate exceeding the operating temperature range. 3. Fluid Do not operate with gases. 4.
Do not mount this kit on other products. Carefully read the procedure manual included with this kit before performing the installation.
Do not expose the product to direct sunlight for an extended period of time. 1/4 12 to 14 3/8 22 to 24 3. Do not use in a place subject to heavy vibration and/or shock. 1/2 28 to 30 4. Do not mount the product in locations where it is exposed to radiant heat. 2.
Please make sure that operating conditions do not cause problems since the use of FEP tubing under chemical environment is unsecured.
Do not use the product in a place where static electricity is a problem.
Do not touch the terminals and connectors while the power is on.
Do not apply fluid under leaking conditions. Safety cannot be assured in the case of unexpected malfunction.
Warning 1 2 Sensor Monitor PF23 4 3 Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. 4 8 Switch output 1 Black Output for PF23 Main circuit Pin number Content Colour 3 7 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not cut the insulator. Do not touch the terminals and connectors while the power is on. Otherwise electric shock, malfunction or damage to the product can result. Toluene 20 mm or more Sheath concentration 50% or less Hydrofluoric acid Do not touch the piping or its connected parts when the fluid is at high temperature. It may lead to burnt.
Do not use in a location having an explosive atmo sphere. 2. Do not operate in locations where vibration or im pact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources. 4. Do not use in environments which exceed the ambi ent temperature specifications of the product. 3.
Do not service or attempt to remove product and machinery/equipment until safety is 3. Do not service or attempt to remove product and machinery/equipment until safety is 3. Do not service or attempt to remove product and machinery/equipment until safety is 3. Do not service or attempt to remove product and machinery/equipment until safety is 3.
Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, steam, or where there is direct contact with any of these. 2. Do not use in potentially explosive environments. 3. Do not mount the product in locations where it is exposed to radiant heat. 4.
Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. Remove drainage from the air filters regularly. 2. Lubrication 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction.
Replace Large exhaust resistance Normal condition (2) Do not disassemble the product. CAUTION Do not replace the sound absorbing material only.