AXTS-OMY0007 Mounting P 11 8. Environment P 11 9. Lubricant oil P 11 10. Air source P 11 -2 - Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Check for air leaks from the fitting and piping. (11) In case of air leakage from the interface, stop air supply and check the mounting condition of the gasket. Tighten the mounting screw with appropriate torque. If the countermeasures above are not effective, there may be a problem with the valve. In that case, stop using the valve immediately.
SUS304> 5 (SUS304) () 2 4 (A6063) < A6063> C D E E F C H B G A A mm A B C D E F G H XLH-16 40 100.5 38 1 30 17 35 XLH-25 50 114 48 1 12 40 26 41 XLH-40 65 162.5 66 2 11 55 41 57 XLH-50 70 179.5 79 2 11 75 52 70 8 XL-OMY0003
5 10 []18 12 O 1) FKM M 10 FKM : 110 Pa <> 9 XL-OMY0003
6 6-1. 1 1P4P5 10 XL-OMY0003
6-2 1 2 b 3 1 2 O 4 a aa b O O
Basic Construction 16 O-ring NBR 15 Piston seal NBR 14 Rod seal NBR Oil-impregnated sintered 13 Bushing bearing 12.
Also, if pipe tape is used, as in Fig. (11), leave 1.5 to 2 thread ridges exposed at the end of the threads. Operating air Air supplied to the rotary actuator shall be cleaned by the filter. CRA1 series is lubrication free.
Note) Tighten within the tightening torque of 0.5 Nm 15%. Note: a) It is possible to wire even in the state of bare wire.
Replace the product in the case of failure such as difficulty removing or inserting tubing. 11 - 5. Construction Male connector Male elbow No.
PP depth element Nominal filtration accuracy: 1 to 75m Material: PP EJ202S ... x 11 (L125) EJ302S ... x 11 (L250) EJ402S ... x 11 (L500) b Set the stopper on the retainer while holding down the V-band outside perimeter, and then tighten the wing bolt to the prescribed position.
Fittings & Tubing Air Cylinders Rotary Actuators How to Order Clean series 11 12 Vacuum suction type Relief type (with specially treated sliding parts) CXSJM, CXSJL CXSJL CXS 6 50 J 11 L M9B S 21 CXS L J 6 50 M9B S Number of auto switches 2 pcs. 1 pc. n pcs.
Input unit 1 connector 2 inputs type 1 Communication socket (BUS) 10 ( ) 12 Supplying power for output instruments such as a solenoid valve with an accessory connector ( ). 11 2 Power supply socket (PWR(V)) Supplying power for controlling GW and for input devices such as a sensor with a power supply connector ( ). 11 3 Power supply socket (PWR) Input unit 1 connector 1 input type connecting
SYJ514 With valve 15 Release valve (N.C.)
HEPO II element Absolute filtration accuracy: 2 to 13m US FDA compatible Nonwoven fabric element with high filtration accuracy of more than 99% removal and without fiber outflow and release of chemical components Material: PP (EJ102S ... x 0) PP depth element Nominal filtration accuracy: 1 to 75m Material: PP EJ202S ... x 11 (L125) EJ302S ... x 11 (L250) EJ402S ... x 11 (L500) Set the
ZH-OM00401 Contents Safety Instructions 2 How to Order 4 Operating Environment 6 Mounting 6 Piping 9 Air Supply 10 Model Selection 11 Ejector Characteristics 11 When Operating the Ejector 12 Identification 12 Construction 13 Specifications 13 Exhaust Characteristics / Flow Rate Characteristics (Representative Value) 14 Circuit Examples 16 Maintenance 18 Trouble shooting (Vacuum Adsorption
Bore Arm angle( (mm) 75 90 105 120 15 30 45 60 135 0 0 0 0 0 0 0 0 0 50 15 30 45 60 75 90 105 120 135 -4 -5 -5 -5 -5 -5 -5 -6 -9 0 0 0 0 0 0 0 0 0 63 15 45 30 60 75 90 105 120 135 -3 -4 -5 -5 -5 -5 -5 -6 -9 (7) Do not disassemble the power clamp cylinder. The power clamp cylinder consists of a completely sealed structure in order to protect it from welding spatter.
3-15 osi A used ptugged 1i2 Snlit t) 3-15 nsi rl plugged USEQ 1/2 Solil B Reverse _z 3-15 osi USEd plugged 1/2 Solil B 3-15 osi A plugged useo 1/2 Snlit D Fig. TO OPERATION SIGNAL RANGE INSTALLATION STYLE (REF.
3-15 osi A used ptugged 1i2 Snlit t) 3-15 nsi rl plugged USEQ 1/2 Solil B Reverse _z 3-15 osi USEd plugged 1/2 Solil B 3-15 osi A plugged useo 1/2 Snlit D Fig. TO OPERATION SIGNAL RANGE INSTALLATION STYLE (REF.
Mounting frame (Option: Refer to page 14-15-1, Accessories.)
No.PS-OMO0002-A PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE3 ISE3(L) Table of Contents Safety Instructions 2 Model Identification and How to Order 8 Summary of Product parts 9 Definition and terminology 10 Mounting and Installation 12 Piping 12 Wiring 13 Pressure Setting 15 2-output type 15 1-output type with the failure predictive function 16 Other Settings 17
Description Material No. 1 Description Material Note 11 Bumper Body Urethane rubber Aluminum alloy Hard anodized High carbon chrome bearing steel 10: Stainless steel 16 to 25: Aluminum alloy 12 Needle roller 2 Piston 16 to 25: Chromated 13 14 15 16 17 18 19 20 3 4 5 6 7 8 9 10 Joint roller Joint Nitriding Stainless steel Carbon steel Heat treated Rubber magnet Finger Stainless steel Synthetic
1 8 AQ3000 AQ1510 45 33 25 4 21 15 25 8 11 4.3 56 50 12.5 56 , , 1 2 3 4 AQ5000 85 75 18 85 15-12-2