IDX-OM-V020 Rubber grommet Signal cable entry Strain relief Power supply cable entry L N PE (to be connected to the user's equipment) Refer to 3-5 for details for electric wiring. IDFA60/70/80/90 Series 2.1Name and Function of Parts 2-1 IDX-OM-V020 Chapter 2 Name and Function of Parts Left ventilation grille (air intake opening) (Dustproof filter) Air intake for cooling.
(PE) port 1. Polarity Caution If the solenoid valve and the manifolds pilot EXH (PE) port is restricted extremely or blocked, abnormal operation of the solenoid valve may occur. When connecting power to a solenoid valve with a DC specification and equipped with a light or surge voltage suppressor, check for polarity. If there is polarity, take note of the following. Mounting 1.
-T: 1300/1500 Temperature stability Note 4) C 2 Circulating fluid system Pump capacity (50/60 Hz) Note 5) MPa 0.08 (at 7 L/min)/0.11 (at 7 L/min) For option -T: 0.13 (at 7 L/min)/0.18 (at 7 L/min) Rated flow (50/60 Hz) Note 6) L/min 7/7 Tank capacity L Approx. 5 Port size Rc1/2 Fluid contact material Stainless steel, Copper (Heat exchanger brazing), Bronze, Brass, Ceramic, Carbon, PP , PE
Stainless (I include heat exchanger brazing), Aluminum oxide ceramic, SiC, Carbon, PP, PE, POM, FKM, EPDM, PVC (No. copper used) Circulating fluid wetted materials Servieable conductivity: 0.22S/cm or more. (Resistivity: 4.5Mcm or less.) This option doesnt include a function to maintain high resistivity/conductivity. You need ion exchange resin filter (DI filter) for the purpose.
Reference data Units: mm IDH6 Jumper cord 7 6 5 4 3 1 PE Remote start/stop Fault-signal (N.O: Close at "Fault") Fault-signal (N.C: Open at "Fault") 1042 31 N 2 L Operation-signal (N.O) Ground Terminal screw: M3 Suitable wire: 1.25mm or more 2 244 Power supply Connector width: 6.5mm or less Detail of wiring 35 184 172 392 (Note) 15 80 223 321 3001 485 The type without built-in filter does
Since PE port is the exhaust port of the pilot valve, do not Terminal + attach a plug or reduce the port diameter. 2. X port is the pressure supply port of the pilot valve and PE port is the exhaust port of the pilot valve. Avoid mismatching when piping. 3. The manual portion contains a breather hole for the core.
(PE) port (R, NPT) (Nm) If the pilot EXH. (PE) port of the solenoid valve is significantly restricted or blocked, the valve operation may become abnormal. 1/4 8 to 12 3/8 15 to 20 1/2 20 to 25 3/4 28 to 30 Mounting 1 36 to 38 1.
Since PE port is the exhaust port of the pilot valve, do not attach a plug or reduce the port diameter. 2. X port is the pressure supply port of the pilot valve and PE port is the exhaust port of the pilot valve. Avoid mismatching when piping. 3. The manual portion contains a breather hole for the core.
X, PE port PCW type There is no need to enter anything when the SUP/EXH block mounting position M is selected. Pilot spec.
Out connector with spanner during piping. 5 Wait 3 minutes before restart. 6 Ensure Running Condition / Evaporating Temp. in green zone. 1 2 3 4 5 6 i 5 IDH Series i.2 IDX-OM-W038 i i.3 HFC i 6 IDH Series i.3 IDX-OM-W038 i i.4 1 1.5 () i.4 i 7 IDH Series IDX-OM-W038 1. 1 1.1. 1-3 10mm 17mm (22mm) 17mm (22mm) IDH Series 11 1.1 IDX-OM-W038 1. () OFF ON () 3 7 6 5 1 2 4 PE
As the PE port is the exhaust port of the pilot valve, do not plug or restrict it. 2. The X port is the pressure supply port of the pilot valve and PE port is the exhaust port of the pilot valve. Pay attention that these ports should be connected correctly. 7 VG300**-OMH0006-A Trouble shooting Perform troubleshooting with higher possibility based on the failure phenomenon.
, (H): SYJ7220-01 Built-in one-touch fitting: SYJ7220G: Approx. 300 H: Approx. 600 (Lead wire length) 107.4 [111.8] 63 3 13 B A B A Manual override 17 35 17 2-3.2 (For manifold mounting) 1/8 (A, B port) One-touch fitting (A, B port) (4.9) 2-3.2 (For mounting) (Light/surge voltage suppressor) Applicable tubing O.D.: 6, 1/4" : 8, 5/16" 35 36 + 28 25 16.1 31.5 [38.5] 21 1.6 P R2 R1 18 1.6 (PE
(included) M3 x 6l Binding band (included) 34 Holding plate (included) 4-M6 x 1 C section 30 D When using a PE terminal, use accessories included as shown above.
The built-in circulator tank is made of resin (PE). Therefore, the tank may be crushed if the pressure is negative. Special attention must be paid if the flow rate of the circulating fluid is high. To avoid a negative pressure of 0.02 MPa or below, the piping return should be as thick and short as possible to minimize piping resistance.
Hz L/min 55/68 Maximum pump head m 50 Minimum operating flow rate 50/60 Hz7 L/min 29/45 Tank capacity L 18 Circulating fluid outlet, circulating fluid return port Rc1 (Symbol F: G1, Symbol N: NPT1) Tank drain port Rc1/4 (Symbol F: G1/4, Symbol N: NPT1/4) Pump capacity Fluid contact material Stainless steel, Copper (Heat exchanger brazing), Brass, Bronze, PTFE, FKM, EPDM, PVC, NBR, POM, PE
PE!$cI;i~tj9h ",' Action Double aCllng single rod Double acti ng single rod 'Model i Standard type CS2 iCS~ ,: Smooth cylinder CS2Y How to Order 0 .. c o C I A With rod end bracke t D o a. ..
Be sure to leave it open as if the PE port is blocked, normal pressure setting cannot be performed.
Note 1) Air consumption is approx. 9.5 L/min (ANR) [at a supply pressure of 1.0 MPa].
Note 2) If there is an abnormal amount of air leakage from the PE port, the diaphragm may be damaged.
(M5 X 0.8), 2 position single solenoid valve, Operating pressure range: 0.15 to 0.7MPa, Response time (ms) (0.5MPa): 15 or less, Low power consumption: 1.8W DC, VALVE SOL 24VDC *LQA, VALVE, VZ2000 SOL VALVE 4/5-PORT, AD, VZ2000 BODY PT Weight: tab 9 0.209 lb
See individual series information for replacements. 4 port solenoid valve, body ported, 2 position single solenoid valve, Operating pressure range: 0.15 to 0.7MPa, Response time (ms) (0.5MPa): 15 or less, Low power consumption: 1.8W DC, VALVE SOL 24VDC *LQA, VALVE, VZ1000 SOL VALVE 4/5 PORT, BD, VZ1000 BODY PT(M5, NON-US STD), 0.19989 lb