Fieldbus system EtherNet/IP TM compatible SI Unit IO-Link Master Unit

Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.

•

Inch' size I0 1/4" 03/8' 05/16" 05/16" diameter . . 03/S' 051160 1/2" Flbw."rate tlin\~ 330 750 350 C ,oP/rolled flow . (A,MR~~N '(lmjQ' . 180 600 1100 1190 [Ereo flaw) Effettive ~IOnal 11.6 17 2.9 5.2 18.4 5.4 9.3 'ttrea mm 2 . N01e} The iMicaled 110w rate values are al a pressure 01 O.5MPa and a temperature 01 20 Q C. 1 Speed Controller 5 .

Cylinder with Lock

Do not turn the piston rod with the rod boot kept locked. When turning the piston rod, loosen the band once and do not twist the rod boot.

Electric Actuator with Integrated Guide

Do not operate beyond the rated voltage range. If applying voltage over the rated voltage range, equipment may be damaged. 2. Avoid incorrect wiring such as polarity of power supply. Otherwise, equipment may be damaged. 3. Do not short circuit the load. (Do not connect to power supply.) Otherwise, equipment may be damaged.

ARM10/11

Do not drop or bump the product. Dropping or bumping while handling may cause damage to the product. 5. Lead wire dimensions Covering: 3.4 Insulator: 1.1 Conductor: 0.64 Pressure Supply Warning 1. Do not use the switch with corrosive gas or liquid. Operating Environment Do not use the switch with corrosive gas or liquid. Such gas or fluid may cause damage to the switch. Warning 2.

ARM10/11

Do not drop or bump the product. Dropping or bumping while handling may cause damage to the product. 5. Lead wire dimensions Covering: 3.4 Insulator: 1.1 Conductor: 0.64 Pressure Supply Warning 1. Do not use the switch with corrosive gas or liquid. Operating Environment Do not use the switch with corrosive gas or liquid. Such gas or fluid may cause damage to the switch. Warning 2.

Air Cylinder

Do not apply excessive lateral load to the piston rod.

Auto Switch Guide

Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.

Soft Start-up Valve

Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water vapor is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in an explosive environment. 3. Do not use in a place subject to heavy vibration and/or impact. 4. The valve should not be exposed to prolonged sunlight. Use a protective cover if necessary. 5.

Round Type Hydraulic Cylinder

Description BA-01, BA-02, BA-32, BA-04, BA-05, BA-06, BA-08, BA-10 BA2-020, BA2-025, BA2-032, BA2-040 BA5-050, BHN2-025, BSG1-032 BH2-040, BH2-050, BH2-080, BH2-100 BAF-32, BAF-04, BAF-05, BAF-06, BAF-08, BAF-10 BJ2-006, BJ2-010, BJ2-016 BM2-020A, BM2-025A, BM2-032A, BM2-040A BMA2-020A, BMA2-025A, BMA2-032A, BMA2-040A, BMA2-050A, BMA2-063A BHN3-025A, BHN3-032A, BHN3-040A D-B5, B6 D-G5, K5

Fluoropolymer Piping Equipment

Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. LVA LVH LVD LVQ When the tubing is curved, straighten it out before using it. Maintenance The tubing may slip if there is oil or dust, etc., on the holder.

End Lock Cylinder Series CBM2/ø20, ø25, ø32, ø40 Series CBA1/ø40, ø50, ø63, ø80, ø100 CL MLGC CNA CB CV/MVG Maintains the cylinder’s CXW original position even if the CXS air supply is interrupted. CXT MX

The lock might not disengage or might become damaged if a load ratio of 50% is exceeded. t Do not synchronize multiple cylinders. Do not operate two or more end lock cylinders synchronized to move a single workpiece because, one of the cylinder locks may not be able to disengage when required. y Operate the speed controller under meter-out control.

A

Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.

JIS Standard Hydraulic Cylinder

Some trunnion mounting positions do not allow auto switch mounting. Please consult with SMC for more information.

Series: 3 (VFA3000), Manifold: 30 (VFA1000 P,R Port Size: 1/8; VFA3000 P,R Port Size: 1/4), Stations: 05, Type: 1 (Common Exhaust), Thread: 00N (NPT)

Series: 5 (VFA5000), Manifold: 20 (P.R Port Size 3/8), Stations: 05, Type: 1 (Common Exhaust), Thread: 00N (NPT)

Series: 1 (VFA1000), Manifold: 30 (VFA1000 P,R Port Size: 1/8; VFA3000 P,R Port Size: 1/4), Stations: 05, Type: 1 (Common Exhaust), Thread: 00N (NPT)

5 Port Air Operated Valve Series SYA3000/5000/7000 1

VR VH Body ported single solenoid Foot bracket VFA3122 F 02 VHS Body ported For 30 type manifold VFA3 1 0 3 02 Base mounted For 40 type manifold VFA3 1 0 4 02 Port size For 50 type manifold VFA3 1 50 W/o sub-plate (Pilot port: Rc) Nil W/o sub-plate (Pilot port: Other than Rc) Thread type for pilot port 00 For 60, 61,70, 71 manifold VFA3 1 0 6 02 02 03 1 4 3 8 Nil 00F 00N 00T Rc G NPT NPTF

Stations: 05, Thread: 00N (NPT)

Model: 7 (10-SY7000), Stations: 05, Thread: 00N (NPT)