AC Servo Motor Driver (Network card type ） A B A B A B A B A B A B A B A B A B 40 50 63 80 100 6 4 4 1 0.5 0.5 1 7 2.5 4.5 12 10 0 0 4 0 1.5 9 8 3.5 6 4 3.5 1.5 1 0 0.5 6.5 2 4 11.5 10 0 0 4.5 0 2 9.5 8 3 8.5 7.5 6 5 4.5 2.5 3 9 4.5 6.5 14 12.5 1.5 2 8 3.5 5.5 13 11.5 5.5 12 10 9.5 7.5 7 6 6.5 12.5 8 10 17.5 16 4 4.5 10.5 6 8 15.5 14 9 13.5 12.5 11 10 9.5 7.5 8 14 9.5 11.5 19 17.5 6.5 7 13 8.5 10.5 18 16.5 10.5 Note) Adjust the auto
b . A b . A b . A 1 2 3 1 b012 Ab. 0 1 b b . A b .
END 1014 Booster Regulator VBA Series Working Principle The IN air passes through the check valve to booster chambers A and B. Meanwhile, air is supplied to drive chamber B via the governor and the switching valve. Then, the air pressure from drive chamber B and booster chamber A are applied to the piston, boosting the air in booster chamber B.
F,N)06A,B(-B,S)(-K,R,Z) VHS5510-(F,N)06~10A,B(-B,S)(-R,Z) Contents PAGE 1.
HED003-W2 A B 13 19 HED003-C2A B (Temperature Controller) HED003-HW13 19 (Heat Exchanger) HED005-W2 A B 13 19 HED005-C2A B (Temperature Controller) HED005-HW13 19 (Heat Exchanger) HED007-W2 A B 13 19 HED007-C2A B (Temperature Controller) HED007-HW13 19 (Heat Exchanger) Keep this manual available whenever necessary.
END 5 Booster Regulator Series VBA Working Principle The IN air passes through the check valve to booster chambers A and B. Meanwhile, air is supplied to drive chamber B via the governor and the switching valve. Then, the air pressure fromdrive chamber B and booster chamber A are applied to the piston, boosting the air in booster chamber B.
r B " " $6y t " 5 ' % " $60C4,D 4 B u % " " B 17-3-98 Series VVXA21/22 Direct Air Operated 2 Port Valve/Manifold For Air, Gas, Vacuum and Oil The VX series will be revised shortly.
AP100 17 735 ARM11A/B Series Pressure Switch Block 56 ARM11AW Z A 0.4 0.2 0.6 0.5 20 MPa 24 q w 0.3 0.1 1. Accessory 2.
For safe operation of SMC Thermo-dryer, thoroughly read and follow the safety instructions, as well as regulations stated within ISO 4414*1 & JIS B 8370*2. *1) ISO 4414: Pneumatic fluid power General rules and safety requirements for systems and their components *2) JIS B 8370: Pneumatic fluid power General rules relating to systems This manual is intended to explain the installation and
This item is U n i t N u m b e r M O D E < 0 applicable only when multiple units are used. 2. Baud Rate B a u d R a t e M O D E < 1 2 0 0 b / s Setting range : 600, 1200, 2400, 4800, 9600, 19200b/s Indicated content : Baud rate (Ex. : 1200b/s) Function : Sets baud rate for communication. 3.
H Non-leak (105atm cc/sec) Brake oil Water (Up to 60C) B P A H Stainless Steel Note 1) The leakage amount(105atm cc/sec)of "V" option is valued when differential pressure is 0.1MPa.
Analog Output Flow/Analog output Output A B C Voltage output 1 V 1.1 V 5 V Current output 4 mA 4.4 mA 20 mA C Model Rated flow [L/min] Minimum Maximum LFE1 0.5 20 LFE2 2.5 100 LFE3 5 200 B A Outside the range 0 Min.
0.2 0.1 0.2 C and b values are for controlled flow with the needle fully open and free flow with the needle fully closed.
(2.5)] VFRA4311-04 3 8 VFRA4411-03 3 position exhaust center 1.2 1 8 PA, B: 51 (2.8) A, BEA, EB: 57.6 (3.2) [A, BEA, EB: 45 (2.5)] 1 2 VFRA4411-04 3 8 65 (3.6) [PA, B: 30.6 (1.7)] VFRA4511-03 3 position pressure center 1.2 1 8 VFRA4511-04 1 2 67 (3.7) [PA, B: 30.6 (1.7)] ( ): in case of normal position.
10A 15A 20A 25A 32A 1 8 1 4 3 8 3 8 1 2 3 4 220 VAC 50/60 Hz Valve size 1 7 5 6 24 VDC 12 VDC B: Slotted locking type B (tool required) 7 240 VAC 50/60 Hz 15 (11) 2 Semi-standard For other rated voltages, please consult with SMC. 20 (14) 3 25 (16) 4 1 1 1 4 32 (22) 5 1 B 1 4 Flange 32F Nil: Non-locking push type 40A 1 1 2 Valve size 2 to 9 40 (28) 6 1 B 1 2 Flange 40F 2 50A 50 (33) 7 50F