VHS The port at a right angle to them is 3(R) port (EXH). Be sure to comfirm before connecting since erroneous connection will cause malfunction. 2. When the valve is exposed to a large amount of dust and debris, install a silencer on 3(R) port (EXH) to protect the valve. Otherwise, dust will ingress from 3(R) port and cause air leakage.
Model no. 1 3 5 A VZ X1 ( ) VZ3 A ( ) Manual override Entry is the same as standard products. Entry is the same as standard products.
P2, L5 X1 S/S . P3, L10 1 2 1 2 1/2 B Thd D A Thd C Hole Dia. Stainless Steel Threaded Parts Page & Part No. Line No. Page & Part No. Line No. D Line No.
Power off is displayed when power is not supplied. 3 Power status Indicates the connection status of the PCNFC reader / writer. 4 R/W connection status R/W undetected: NFC reader / writer is not identified or USB is not connected.
Body Size: 4, Thread: Rc, Port Size: 06 (3/4), Handle/Bonnet Material: B (Aluminum), Options: S (Built-in Silencer, EXH Port), Semi-Standard: R (Flow Direction: Right to Left), Made to Order: X1 (Body: Red)
Body Size: 4, Thread: Rc, Port Size: 04 (1/2), Handle/Bonnet Material: A (Flame Resistant PBT), Options: S (Built-in Silencer, EXH Port), Semi-Standard: R (Flow Direction: Right to Left), Made to Order: X1 (Body: Red)
Regulator Unit Combination: [Other FRL Combination Devices] Other FRL Combination Device, Port Size: Rc3/4, Compressed Air Quality: General Dry Air, Maximum Operating Pressure(MPa): 1, Case Material: [Resin] Polycarbonate Case, Case Guard: No, Exhaust Structure: Relief type, Flow Direction: [Reverse Flow (Right to Left)] Right to left, Drain Cock: [Not Provided] No, Pressure Gauge: -, Size
Body Size: 4, Thread: Rc, Port Size: 1/2, Handle/Bonnet Material: Flame Resistant PBT, Options: Built-in Silencer, EXH Port, Semi-Standard: Flow Direction: Right to Left, Made to Order: Body: Red
HOLD keykey SVON DRIVE RESET SETUP JOGJOG+ FLGTH MODE WRST Brake Origin SW: Origin switch Origin SW Limit SW-F: Limit switch F side Limit SW-F Limit SW-R: Limit switch R side EMS: Stop (Normal close) Limit SW-R EMS [ ] Stop Enable SW EMS [ ] Stop cancelled EMS 90 - (6-3-4) Output pin monitor It is possible to monitor the output pin of the controller with the pin number. (6-
How to Order IR 2 0 0 02 R 0 Pressure gauge mounting Precision regulator Body size R Note) Pressure gauge mounted on reverse side Type of setting Note) The standard mounting position of the pressure gauge is on the front, when viewing the regulator with the SUP side to the left and the OUT side to the right. 1 2 3 IR1000 IR2000 IR3000 Basic type (handle) Air operated type (series IR2000/3000
Model no. 1 3 5 A VZ X1 ( ) VZ3 A ( ) Manual override Entry is the same as standard products. Entry is the same as standard products.
This is a legacy product, and replaced byVHS40-04B-R, VALVE, 3 PORT LOCK OUT, VALVE, VHS HAND VALVE, JA, VHS BODY PT 1/2, .83658 lb
Construction 1 4 1 4 1 3 1 6 6 2 5 5 7 Connection thread: G Connection thread: R,NPT Male connector Male elbow Swivel elbow No.
Body Size: 4, Thread: Rc, Port Size: 04 (1/2), Handle/Bonnet Material: B (Aluminum)
Regulator Unit Combination: [Other FRL Combination Devices] Other FRL Combination Device, Port Size: Rc1/2, Compressed Air Quality: General Dry Air, Maximum Operating Pressure(MPa): 1, Case Material: [Resin] Polycarbonate Case, Case Guard: No, Exhaust Structure: Relief type, Flow Direction: [Standard Flow (Left to Right)] Left to right, Drain Cock: [Not Provided] No, Pressure Gauge: -, Size
In this document TM and (R) are not specified. -EtherCAT is registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany. -83No.
Body Connection Thread Tightening Method Caution (1) Fittings with sealant: R, NPT 1) First, tighten the fitting by hand, then use a wrench appropriate for the hexagon flats of the body to tighten it a further two or three turns. For a tightening torque guide, see the table below. If the fitting is tightened with excessive torque, the fitting may break.
www.stevenengineering.com A C T U AT O R S P R O D U C T S E L E C T O R PA G E 1.1 VA LV E S P R O D U C T S E L E C T O R PA G E 2.1 F L O W C O N T R O L E Q U I P M E N T P R O D U C T S E L E C T O R PA G E 3.1 F I T T I N G S A N D T U B I N G P R O D U C T S E L E C T O R PA G E 4.1 A I R P R E PA R AT I O N P R O D U C T S E L E C T O R PA G E 5.1 VA C U U M P R O D U C T S E L E
Zero speed detection ZSP ZSP turns on when the servo motor speed is zero speed (50 r/min) or less. Zero speed can be changed with [Pr. PC07]. OFF level 70 r/min 1) Forward rotation direction 3) 2) 20 r/min (Hysteresis width) ON level 50 r/min [Pr. PC07] Servo motor speed 0 r/min [Pr.
P R R P R R L (10) 8 End plate side End plate side (24) (35) 5.5 Silencer with One-touch fitting The silencer plugs directly into the One-touch fittings of the manifold.