Stations: 8 Stations, A, B Port: 03B (Side/Bottom, Side Plugged 3/8), SI Unit: QW (DeviceNet), P, R Port Size: 04 (1/2), P, R Port Location: B (Both Sides), Thread: T (NPTF)
LEC-OM005xx HOLD keykey SVON DRIVE RESET SETUP JOGJOG+ FLGTH MODE WRST Brake Origin SW: Origin switch Origin SW Limit SW-F: Limit switch F side Limit SW-F Limit SW-R: Limit switch R side EMS: Stop (Normal close) Limit SW-R EMS [ ] Stop Enable SW EMS [ ] Stop cancelled EMS 90 - (6-3-4) Output pin monitor It is possible to monitor the output pin of the controller with the pin number. (6-
How to Order IR 2 0 0 02 R 0 Pressure gauge mounting Precision regulator Body size R Note) Pressure gauge mounted on reverse side Type of setting Note) The standard mounting position of the pressure gauge is on the front, when viewing the regulator with the SUP side to the left and the OUT side to the right. 1 2 3 IR1000 IR2000 IR3000 Basic type (handle) Air operated type (series IR2000/3000
Model no. 1 3 5 A VZ X1 ( ) VZ3 A ( ) Manual override Entry is the same as standard products. Entry is the same as standard products.
Construction 1 4 1 4 1 3 1 6 6 2 5 5 7 Connection thread: G Connection thread: R,NPT Male connector Male elbow Swivel elbow No.
Body Size: 4, Thread: Rc, Port Size: 03 (3/8), Handle/Bonnet Material: B (Aluminum)
Regulator Unit Combination: [Other FRL Combination Devices] Other FRL Combination Device, Port Size: Rc3/8, Compressed Air Quality: General Dry Air, Maximum Operating Pressure(MPa): 1, Case Material: [Resin] Polycarbonate Case, Case Guard: No, Exhaust Structure: Relief type, Flow Direction: [Standard Flow (Left to Right)] Left to right, Drain Cock: [Not Provided] No, Pressure Gauge: -, Size
This is a legacy product, and replaced byVHS30-03B-R, VALVE, 3 PORT LOCK OUT, VALVE, VHS HAND VALVE, HA, VHS BODY PT 3/8, .66171 lb
Body Size: 40, Thread: Rc, Port Size: 03 (3/8), Handle/Bonnet Material: B (Aluminum), Options: None, Semi-Standard: R (Flow Direction: Right to Left), Made to Order: X1 (Body: Red)
Body Size: 30, Thread: Rc, Port Size: 03 (3/8), Handle/Bonnet Material: B (Aluminum), Options: None, Semi-Standard: R (Flow Direction: Right to Left), Made to Order: X1 (Body: Red)
Body Size: 40, Thread: Rc, Port Size: 3/8, Handle/Bonnet Material: Aluminum, Options: None, Semi-Standard: Flow Direction: Right to Left, Made to Order: Body: Red
Regulator Unit Combination: [Other FRL Combination Devices] Other FRL Combination Device, Port Size: Rc3/8, Compressed Air Quality: General Dry Air, Maximum Operating Pressure(MPa): 1, Case Material: [Resin] Polycarbonate Case, Case Guard: Presence, Exhaust Structure: Relief type, Flow Direction: [Reverse Flow (Right to Left)] Right to left, Drain Cock: [Not Provided] No, Pressure Gauge:
In this document TM and (R) are not specified. -EtherCAT is registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany. -83No.
Body Connection Thread Tightening Method Caution (1) Fittings with sealant: R, NPT 1) First, tighten the fitting by hand, then use a wrench appropriate for the hexagon flats of the body to tighten it a further two or three turns. For a tightening torque guide, see the table below. If the fitting is tightened with excessive torque, the fitting may break.
www.stevenengineering.com A C T U AT O R S P R O D U C T S E L E C T O R PA G E 1.1 VA LV E S P R O D U C T S E L E C T O R PA G E 2.1 F L O W C O N T R O L E Q U I P M E N T P R O D U C T S E L E C T O R PA G E 3.1 F I T T I N G S A N D T U B I N G P R O D U C T S E L E C T O R PA G E 4.1 A I R P R E PA R AT I O N P R O D U C T S E L E C T O R PA G E 5.1 VA C U U M P R O D U C T S E L E
Zero speed detection ZSP ZSP turns on when the servo motor speed is zero speed (50 r/min) or less. Zero speed can be changed with [Pr. PC07]. OFF level 70 r/min 1) Forward rotation direction 3) 2) 20 r/min (Hysteresis width) ON level 50 r/min [Pr. PC07] Servo motor speed 0 r/min [Pr.
P R R P R R L (10) 8 End plate side End plate side (24) (35) 5.5 Silencer with One-touch fitting The silencer plugs directly into the One-touch fittings of the manifold.
Speed Rated speed 0 r/min Time [Pr. PC01] setting (0 mm/s) [Pr. PC02] setting For example for the servo motor of 3000 r/min rated speed, set 3000 (3 s) to increase the speed from 0 r/min to 1000 r/min in 1 second.
D E R S E R I E S ADH 4000 H E A V Y A U T O D R A I N S Y M B O L S ADH4 00 04 T H R E A D .Rc(PT) N .NPT M A X.
Scale: 25% For external pilot specification (Pitch) P = 24 24.3 22.2 11 18.3 3/5 R 3/5 R A 4 A 4 A 4 A 4 A 4 A 4 40.1 39.3 18.8 18 18.8 3/5 R 3/5 R A 4 A 4 A 4 A 4 A 4 A 4 39.3 63.3 79.8 1 P 1 P B 2 B 2 B 2 B 2 B 2 B 2 2-Plug 1 P 1 P B 2 B 2 B 2 B 2 B 2 B 2 [1 (P), 3/5 (R) port] 2-One-touch fitting One-touch fitting 2n1-One-touch fitting [1 (P), 3/5 (R) port] Applicable tube O.D.: 12 [PE: