Digital Flow Switch (Integrated display type)

External input does not operate No reaction to the external input The input signal duration is too short Check that the white input wire is connected to GND for 30 ms or more.

5-Port Solenoid Valve

(Effective energizing time is over 67 ms at 24 VDC.)

Controller/Driver LEC/JXC Series <Single Axis Controllers> Step Data Input Type Page 560 Gateway Unit Page 572 Programless Type Page 576 Step Motor LEC-G Series Step Motor Servo Motor (Servo/24 VDC)/ (Servo/24 VDC)/ (24 VDC)/ LECP6 Series LE

Positioning Operation Pushing Operation ON OFF ON OFF IN IN Input Input 15 ms or more Output the step data no. 15 ms or more Output the step data no.

Wireless System

Wireless System RoHS Usable even in welding environments High-speed connection Noise resistance Communication response Signal response time: 5 ms Uses the 2.4 GHz ISM frequency band Frequency hopping: Every 5 ms From power supply ON to start of communication: Min. 250 ms*1 *1 For wireless slave Communication cables not required Compatible protocol Number of I/O points Reduced wiring work,

JXCx-OMY0006

Incorrect wiring MS: Green LED flashes (1) Setting error (2) PLC has stopped operating, (1) Set up configuration configuration correctly. or the communication is idling. (2) Set PLC in RUN status. MS: Red LED flashes Set up the configuration correctly. Refer to Hardware Configuration (P.20) for details. Recoverable error MS: Red LED is on Unrecoverable error Stop using the product.

Step Motor Driver （ Pulse input type ）

Inappropriate specifications Leave an interval of a minimum of 15 ms (recommendation is 30 ms) between input signals and maintain the state of the signal for a minimum of 15 ms (recommendation is 30 ms), because PLC processing delays and driver scanning delays can occur. 8.4 Response time for the driver input Check the timing of the signal from the PLC to the driver.

EtherNet/IP TM Compatible Fieldbus System

Check the state GW unit MS LED Refer to fault of the GW unit. is OFF. No.1. GW unit MS LED Refer to fault is ON red. No.2. GW unit MS LED Refer to fault is flashing red. No. 3. GW unit MS LED is flashing green. Refer to fault No. 4. GW unit NS LED Refer to fault is OFF. No. 5. GW unit NS LED is Refer to fault ON red No. 6. GW unit NS LED is Refer to fault flashing red. No. 7.

Title not found

;200 million cycles VQC21fi): 20 ms 2 ms;2fi) million cycles For r,lf, srunh vQc4loo: 17 ms 3 ms; 100 million cycles P!

2-Color Display ® Digital Flow Switch *1 Applicable fluid Dry air, N2, Ar, CO2

PNP + Analog output type PF2M7mm-m-Em-mmm PF2M7mm-m-Fm-mmm Load White OUT2 (PF2M7 -B only) or 0 V 50 ms 50 ms 16 PF2M7(-L) Series Internal Circuits and Wiring Examples PF2M7mm-m-Lm-mmm NPN output type PNP output type Brown DC (+) Brown DC (+) Load U Main circuit Main circuit Main circuit Main circuit Black OUT1 Black OUT1 18 to 30 VDC + + Load Load 18 to 30 VDC U White N.C.

3-Screen Display Multi-channel Digital Sensor Monitor Up to 4 pressure sensors can be connected!

Momentary change Pressure Set value P_1 H_1 t (ms) t (ms) Time Switch output operation under normal conditions ON OFF Time Switch output operation when anti-chattering function is on ON OFF Time Pressure range/Unit selection function (F0) Pressure range and displayed units can be switched with this function.

KJ

H D MS T T (with seal) VMG Hexagon Socket Head Male Connector: KJS Connection thread (T) UNF NPT <10-32 UNF> <10-32 UNF> Applicable tubing O.D.

2-Color Display

Available response time settings 20 ms, 100 ms, 500 ms, 1000 ms, 2000 ms Principle This function averages pressure values measured during the response time set by the user and then compares the average pressure value with the pressure set point value to output the result on the switch.

SYJ300/500/700

(Effective energizing time is over 62 ms at 24 VDC.)

9.8

Available response time settings 20 ms, 100 ms, 500 ms, 1000 ms, 2000 ms This function averages pressure values measured during the response time set by the user and then compares the average pressure value with the pressure set point value to output the result on the switch.

Digital Pressure Switch

ZSE20CF : 5.0 kPa ISE20CH : 0.100 MPa Delay time Delay time of the switch output can be selected. 1.5 ms or less Display color Selects the output according to the display color. OUT1 ON : Green OUT1 OFF: Red -30No.PS-OMU0009-D [F 2] Setting of OUT2 Page 36 Same setting as [F 1] OUT1.

Digital Pressure Switch

ZSE20A : 5.1 kPa ZSE20AF : 5.0 kPa Delay time Delay time of the switch output can be selected. 1.5 ms or less Display color Selects the output according to the display color. OUT1 ON : Green OUT1 OFF: Red -28No.PS-OMU0003-D [F 2] Setting of OUT2 Page 34 Same setting as [F 1] OUT1.

Digital Pressure Switch

ZSE20B : 5.1 kPa ZSE20BF : 5.0 kPa Delay time Delay time of the switch output can be selected. 1.5 ms or less Display color Selects the output according to the display color. OUT1 ON : Green OUT1 OFF: Red -29No.PS-OMU0006-D [F 2] Setting of OUT2 Page 35 Same setting as [F 1] OUT1.

Electromagnetic Digital Flow Switch

50 ms PNP 2 output type LFElBlll Brown DC (+) Black OUT1 Max. 80 mA Load White OUT2 0 V or Load 50 ms 50 ms * When accumulated pulse output is selected, the indicator light is turned off.

D-F6N/D-F6P/D-F6B

The operating time for D-J51 is 2 ms or less and for D-P3DW/P4DW are 40 ms or less. 4) 980 m/s2 for the trimmer type sensor section, 98 m/s2 for the amplifier section.

ZSE30A(F)/ISE30A

Available response time settings 20 ms, 100 ms, 500 ms, 1000 ms, 2000 ms This function averages pressure values measured during the response time set by the user and then compares the average pressure value with the pressure set point value to output the result on the switch.