ML1 This air should be 0.4 to 0.5MPa. wLoosen the manual override (nickel plated) rod on the slide table, and draw the rod until it reaches to the end. The size of the hexagon wrench should be 3mm (ML1C25, 32) or 4mm (ML1C40). eExhaust the air to release the brake. Manual rod drawing dimensions Part No.
The resulting impact cannot be absorbed easily, the stroke position cannot be maintained, and faulty operation may result. 5. Lubrication The bearing can be used in an oilless state, but when you are going to oil the bearings, do so by using a ball-cup so that no foreign matter will be mixed. For the grease, we recommended using high-quality lithium soapbased grease no. 2.
(Be sure to put the auto switch on the surface of cylinder tube.) 3. When changing the detecting position, loosen the set screw to move the auto switch and then re-fix the auto switch on the cylinder tube. (Tightening torque of M4 screw should be 1 to 1.2 Nm.)
Safety cannot be assured in the case of unexpected malfunction. Provide grounding to assure noise resistance of the product. Individual grounding should be provided close to the product with a short cable. Caution Notice: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
To use PFA tube in a chemical environment, tests should be performed with the same environment to ensure no problem occurs with operating environment.
Safety cannot be assured in the case of unexpected malfunction. Provide grounding to assure noise resistance of the product. Individual grounding should be provided close to the product with a short cable. Caution Notice: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
If frequent cleaning will be necessary, it can be suspended from the top panel of the tank. t If a fluid switch (built-in lead switch) or the like is used, it should be installed in a location where it will not be affected by magnetism from the separator. (Refer to the technical data sheet (FGX-TDT011) for information on magnetic fields.) Maintenance q Clean the separator regularly.
PLUMBING Be surethatthe supply lines are thoroughly deaned out before connecting to the valve. Any metal chips or other types of contamination should be removed before ooeralion. 1-2 = Solenoid Connection 3 = Ground MANUAL OPIRATION This valve may be manually operated.
PLUMBING Be surethatthe supply lines are thoroughly deaned out before connecting to the valve. Any metal chips or other types of contamination should be removed before ooeralion. 1-2 = Solenoid Connection 3 = Ground MANUAL OPIRATION This valve may be manually operated.
The cylinder ports are designed so that a maximum speed 3000 mm/s can be obtained. However, it may not be possible to attain the desired speed in the case of short cylinder strokes. It may also be impossible to attain the desired speed due to restriction by component equipment (valves, speed control valves, piping, fitting, etc.).
However, be aware that its anti-corrosion performance is inferior to austenitic stainless steel. In particular, the finger might be rusted in an environment where water droplets are adhered to it due to dew condensation. 722 MHY2/MHW2 Series Specific Product Precautions 2 Be sure to read this before handling the products.
A contact protection box should be used in any of the above conditions. Otherwise, the life of the contacts may be reduced. (They may stay on continuously.)
Cycle time can be drastically reduced compared with existing low speed cylinder (10 to 30 mm/s).
applied to pipe line (Line pressure) [the pressure difference in a solenoid valve must be maintained less than the highest operating pressure difference.] r Symbol The JIS symbol is ( ): this designates the valve to be normally closed.
Cycle time can be drastically reduced compared with existing low speed cylinder (10 to 30 mm/s).
The tightening torque should be approximately 0.1 to 0.2Nm for types D-A9 and D-F9, and 0.05 to 0.1Nm for types D-Z7, D-Z8, D-Y5, DY6 and D-Y7. As a rule, the mounting screw should be turned about 90 past the point at which tightening can first be felt.
VXA3114-01 PA PAX PB 17-3-103 8 The VX series will be revised shortly.
These can be mounted on all filter models. Differential pressure indicator Operating pressure0.275 MPa Once a value is displayed, it will continue to be displayed until reset, even if the pump is stopped.
For female rod end, since the wrench flap (K and KA portions) will be inside of the bracket when the piston rod is retracted at the stroke end, extend the piston rod to tighten the nut using a tool, and mount a workpiece on the rod end.
These can be mounted on all filter models. Differential pressure indicator Operating pressure0.13 MPa Once a value is displayed, it will continue to be displayed until reset, even if the pump is stopped.