KJ Tightening of M3 and M5 screws 1) After tightening by hand, the barb elbow type (M-3ALU-2, M5ALHU-2) should be tighten an additional 1/3 rotations using an appropriate wrench. 2) After tightening by hand, other types should be tightened by an additional 1/6 rotations using a suitable tool.
When the product is used for an actuator operating vertically, the actuator may lurch depending on the load. For the adjustment method, please refer to Selection and Adjustment on page 15-16-6 to 15-16-7. 4. For installation and removal, tighten the body B by applying an appropriate wrench to the two opposite sides of the hexagon. Using other parts may destroy the valve.
Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines.
30 14 Connection thread 18.5 16.2 8 Connection thread 23.3 6 17 17.2 10.0 5 17 21 10 27.5 39.0 26.6 3 8 KGS10-03 21 19 8 1 2 KGS10-04 28 22 20 35 23 18 1 4 3 8 KGS12-02 KGS12-03 27.5 22.5 8 33.5 29 28 46.0 19 12 22 44.5 1 2 KGS12-04 20 10 30 Reference dimensions after R thread installation. 60.0 22 Note) D: Max. diameter 15-3-10 Stainless One-touch Fittings Series KG Female Connector: KGF
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
132 20 47 33 12 25 70 M8 X 1.25 40 38 188 Rc(PT)1/8 60 92 125 44 95 20 70 73 162 25 58 82.5 40.5 14 26 M8 X 1.25 45 50 241 Rc(PT)1/8 75 104 150 55 115 20 Without rear plate Long stroke Bracket mounting stroke Bracket mounting stroke Stroke range (mm) Bore (mm) Bore (mm) Bore (mm) Y R Z 20 25 32 40 50 20 25 32 40 50 20 25 32 40 50 100st or more 250 to 400 88 14 119 125st or more 350 to 500
IFW5 10 03 N 1 1 PSE Z I SE3 Diaphragm style flow switch PS Light 0 None Z I SE1 2 1 With neon light (110 VAC, Red) 2 With neon light (110 VAC, Green) Flow range ZSP 3 With neon light (220 VAC, Red) Low flow setting possible (1 l/min) 10 1 to 10 l/min 4 With neon light (220 VAC, Green) 20 10 to 20 l/min Simple flow setting Without removing the cover, you can set with a screwdriver from
Type 60PH: Flat ribbon cable (10 pins) Type 60J: Flat ribbon cable (20 pins, PC wiring) Terminal no.
Series KS Blue Series KX Blue Slide bearing Smooth operation and longer life from an oil containing slide bearing. Rotary seal A special rotary seal minimizes friction while providing an excellent seal. Series KX (High speed) Scraper Holder Prevents chips from intruding into bearing parts. Standard nickel plated allows copper-free applications.
Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines.
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
Never use in an environment, where flammable fluids or gases are used. Since this product is not explosion-proof and may trigger an explosive disaster. 1. Bellows assembly is available for maintenance. When replacing other parts, please contact SMC, since it cannot be repaired by user.
Excessive torque or holding it at an area other than the specified portion may result in a malfunction. 2. While piping to products or operating the handle, ensure that an excess bending moment should not be applied to a product, because it may result in damage. MAX. 2.5t AV AU AF AR IR Component Parts Replacement Parts No. Description Part no. 13434-30 No.
(at 20C) Burst pressure 0.8 MPa 3.0 Burst pressure Refer to the burst pressure characteristics curve. 2.0 Ambient and fluid temperature 20 to 60C Water: 0 to 40C (No freezing) Max. operating pressure 1.0 Internal tubing Polyurethane Outer layer Material Polyolefin (Equivalent to UL-94 standard V-0) 0 20 0 20 40 60 Note) The color of all inner tubing is black.
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
Operate this product in an area in which the air pressure does not exceed 1.6 MPa. If this value is exceeded, it could lead to an accident or malfunction. 2. An air pressure of 0.05 MPa and an air compressors discharge flow rates higher than 50 l/min (ANR) are required. Below these values, the air will continue to be discharged from the drainage discharge port. 3.
TS0425G-500-X3 20 m roll Inch size: Suffix -X4 to the end of part number. Ex.) TISA01BU-20-X4 Made to Order Availability Length Model Part no.
52 : 1 3/4-12 85 : M24 x 1.5 25 : 5/8-11 53 : 1 3/4-5 86 : M26 x 1.5 26 : 5/8-18 54 :1 7/8-12 87 : M30 x 1.5 FEMALE ROD DIAMETER BORE (INCH) A B C MM KK WF 150 (1.5) 3/4 1 1/8 3/8 5/8 7/16-20 1 200 (2) 3/4 1 1/8 3/8 5/8 7/16-20 1 250 (2.5) 3/4 1 1/8 3/8 5/8 7/16-20 1 325 (3.25) 1 1/8 1 1/2 1/2 1 3/4-20 1 3/8 400 (4) 1 1/8 1 1/2 1/2 1 3/4-20 1 3/8 22 Air Cylinder Extended Series NCA1 PARTS
In voltage drop, the allowable voltage range of load should be confirmed. 4 lf an internal resistance of the light emitting diode causes trouble, the switches with no indicator lamp (D-AB) should be used. Senbs NCY2 Specifications for made to order models Contact SMC lo. the details of dimensions, speclflcations, and date of dellvery.