How to Mount a Compact Slide A compact slide can be mounted from 4 directions. Make a selection suitable for the applicable machinery and workpieces, etc.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Hv Auto Switch Proper Mounting Position Solid state auto switch Bore size (mm) 2-color indication solid state auto switch Reed auto switch B C A B Hv A B C A B Hv A B Hv A B C D-A9 D-A9V D-M9 D-M9V D-F8 D-M9W A B Hv D-M9WV A 36 25 16 36 25 15 32 21 20 32 21 17.5 18 7 25 32 21 20 32 21 17.5 8 Note) Adjust the auto switch after confirming the operating conditions in the actual setting.
A large amount of gripping force is provided through the use of a double piston mechanism, while maintaining a compact design. Double-end type oil-impregnated resin bearings with a metal backing are used for all shafts.
If a workpiece is still being held, there is a danger of it being dropped. 7.
If a workpiece is still being held, there is a danger of it being dropped. 7.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
MGPWM MGPWL/A MGPWM MGPWL/A MGPWM MGPWL/A MGPWM MGPWL/A MGPWM MGPWL/A 1.63 1.74 1.51 1.34 1.08 0.99 1.20 2.10 20 4.36 3.46 2.87 3.93 3.07 2.76 3.45 3.97 2.74 3.28 2.90 2.59 2.14 1.97 2.34 3.53 25 6.78 5.43 4.51 6.27 4.90 4.40 5.51 6.88 6.39 7.00 6.19 5.54 4.59 4.22 5.02 7.98 32 8.48 11.14 9.36 12.46 9.83 8.87 11.00 11.13 7.04 7.72 6.82 6.11 5.06 4.66 5.54 8.80 40 9.34 12.27 10.31 13.73 10.83
Use this as a standard when mounting, etc. Auto switches have hysteresis similar to micro switches. Use the table below as a guide when adjusting auto switch positions.
Series ZCUK Free Mount Cylinder for Vacuum A free mount cylinder with a vacuum passage in the rod to meet the requirements for Air cylinder + Vacuum pad . ZA ZX A vacuum passage has been provided in the rod of the CUK cylinder to enable a vacuum pad to be installed on the end of the rod. ZR ZM ZMA ZQ ZH ZU ZL ZY ZF Not necessary to provide vacuum tubing space at the end of the rod.
Use the table as a guideline for mounting.
A B (mm) Model A 21h9 28h9 35h9 35h9 B 2 2 2 2 Weight (g) 805 1,097 1,943 2,825 MHT2-32DZ-X5070 MHT2-40DZ-X5070 MHT2-50DZ-X5070 MHT2-63DZ-X5070 0 0.052 0 0.052 0 0.062 0 0.062 653 A
The cancel cap holds the lever horizontally allowing a pallet to pass.
For example, the bore size to move a workpiece with a weight of 37 kg requires a bore size of 43 or more.
Since the seal kit does not include a grease pack, order it separately.
Tightening with a torque above the limit could malfunction. Whereas tightening insufficiently could result in misalignment or come to a drop. 5. Be careful when adjusting stroke not to allow cylinder end plate to bottom out against cylinder body.
MGP-A 25 16 25 16 50 2025 50 50 20 1 2 21 22 NBR 23 24 25 63100 26 NBR 27 NBR 28 29 A NBR 30 B NBR 31 C NBR 1625 32100 1663 80100 5 1625 32100 7 8 9 10 11 12 13 16 20100 15 16 17 18 19 3 16 1650 4 6 / (mm) (mm) 16 MGP16-A-PS 50 MGP50-A-PS 20 MGP20-A-PS 63 MGP63-A-PS 25 MGP25-A-PS 80 MGP80-A-PS 32 MGP32-A-PS 100 MGP100-A-PS 40 MGP40-A-PS
A part B part Procedure Calculation Calculation example 1. Check the operating conditions, dimensions of attachment, etc. Operating model: MHY2-16D Opening time: 0.15 s a = 40 (mm) b = 7 (mm) c = 8 (mm) d = 5 (mm) e = 10 (mm) f = 12 (mm) A part a b c B part e f d 2.
Use the table as a guideline for mounting. Auto switch mounting bracket part no. BMG2-012 Auto switch part no. D-M9(V)/M9W(V)/M9A(V) Note) Use a screwdriver with a grip diameter of 5 to 6 mm to tighten the set screws (M2.5). The tightening torque should be 0.5 to 1 Nm. As a rule, it should be turned about 90 beyond the point at which tightening can be felt.
H L A H L A H L A H RB 0805 + with adjusting bolt A H A Unit symbol RB 0806 + with adjusting bolt RB 1007 + with adjusting bolt RB 1007 + with adjusting bolt RB 1412 + with adjusting bolt RB 1412 + with adjusting bolt RB 2015 + with adjusting bolt RB 1412 + with adjusting bolt RB 2015 + with adjusting bolt MY2C With adjusting bolt With adjusting bolt With adjusting bolt With adjusting bolt