Series CM2-Z add on single and double piston rod knuckle joints.
SINGLE KNUCKLE JOINT, ROUND BODY CYLINDER, 437, 20.00000 lb
Add 47 mm for each additional I/O Units. m is number of I/O Units.
020B/032B Material: Rolled steel I-040B Material: Free cutting sulfur steel Y (Max.)
1 mounting nut Trunnion nut 1 TN-020B TN-032B TN-040B 1 trunnion nut Single knuckle joint 1 I-020B I-032B I-040B 1 single knuckle joint Double knuckle joint 1 Y-020B Y-032B Y-040B 1 double knuckle joint, 1 clevis pin, 2 retaining rings Clevis pin (Double clevis) 1 CDP-1 CDP-2 1 clevis pin, 2 retaining rings (split pins) Clevis pin (Double knuckle joint) 1 CDP-1 CDP-3 1 clevis pin, 2 retaining
I I I I I I I I I I I I I I I I F79 F7P J79 F79W F7PW J79W F7NV F7PV F7BV J79C F7NWV F7BWV 3-wire (NPN) IC circuit 5 V,12 V Grommet 3-wire (PNP) Reed auto switch Solid state auto switch 2-wire 12 V Connector 3-wire (NPN) Yes 24 V Relay, PLC IC circuit 5 V,12 V Diagnostic indication (2-color indication) 3-wire (PNP) Grommet 2-wire 12 V 3-wire (NPN) 3-wire (PNP) 2-wire 4-wire
020B, 032B Material: Rolled steel I-040B Material: Free cutting sulfur steel Y (Max.)
L1 D-X 243 CQ2Y Series Dimensions of Accessories Single Knuckle Joint Double Knuckle Joint For I-G012, I-Z015A I-G02, I-G03 For I-G04, I-G05 I-G08, I-G10 For Y-G012, Y-Z015A Y-G02, Y-G03 For Y-G04, Y-G05 Y-G08, Y-G10 ND hole H10 Axis d9 ND hole H10 Axis d9 Material: Carbon steel Surface treatment: Nickel plating Material: Cast iron Surface treatment: Nickel plating (mm) Material: Carbon
020B/032B Material: Rolled steel I-040B Material: Free cutting sulfur steel Y (Max.)
I-020B I-032B I-040B +0.058 0 +0.058 0 +0.070 0 0.1 0.2 0.1 0.2 0.1 0.3 9 9 9 48 18 20 38 M10 x 1.25 9 10 14 16 69 22 24 55 M14 x 1.5 12 15.5 20 Use a thin wrench when tightening the piston rod.
020B, 032B Material: Rolled steel I-040B Material: Free cutting sulfur steel Y (Max.)
020B, 032B Material: Rolled steel I-040B Material: Free cutting sulfur steel Y (Max.)
020B, 032B Material: Rolled steel I-040B Material: Free cutting sulfur steel Y (Max.)
I-020B I-032B I-040B E1 L1 MM H A1 MM +0.058 0 +0.058 0 +0.070 0 0.1 0.2 0.1 0.2 0.1 0.3 +0.058 0 +0.058 0 +0.070 0 0.1 0.2 0.1 0.2 0.1 0.3 9 14 10 16 20 36 M8 X 1.25 9 9 10 14 18 46 66 41 9 M8 X 1.25 M10 X 1.25 9 14 10 18 20 38 9 9 10 14 22 48 69 45 9 M10 X 1.25 M14 X 1.5 15.5 16 20 14 22 24 55 12 16 20 24 69 92 50 12 M14 X 1.5 Double Knuckle Joint (mm) Bore size 20 25/32 40 A L NX2 R2 U2
Applicable rod end nut Bore size (mm) I type single knuckle I-12 I-14 I-16 I-18 I-20 I-25 I-30 Y type double knuckle Y-12 Y-14 Y-16 Y-18 Y-20 Y-25 Y-30 I type single knuckle I-12A I-14A I-16A Y type double knuckle Y-12A Y-14A Y-16A 125 140 160 180 200 250 300 NT-12 NT-12 NT-16 NT-18 NT-20 NT-25 NT-30 125 65 100 181 18 CS1 CS2 125 65 105 186 18 140 76 110 198 21 155 83 125 223 23 -X -X 160
Bore size (mm) Description 20 25 32 40 CM-L020B-XB12 CM-L040B-XB12 Foot (1) CM-L032B-XB12 CM-F020B-XB12 CM-F040B-XB12 Flange CM-F032B-XB12 SN-020BSUS SN-040BSUS Mounting nut SN-032BSUS NT-02SUS NT-04SUS Rod end nut NT-03SUS Single knuckle joint I-020B-XB12 I-040B-XB12 I-032B-XB12 Double knuckle (2) joint Y-020B-XB12 Y-040B-XB12 Y-032B-XB12 Pin for double (3) knuckle joint CDP-3-XC27 CDP-1
0 i q o u y !7 r !9 w !4 CY3B10, 15 !4 !8 !7 !6 !5 !0 i o q u y t r !2 w !1 The above drawing is 15. (3 magnets are used in 10.) CY3B20 to 40 !3 !4 !1 !8 !6 !5 !7 !0 i q o u t y r e w !2 CY3B50, 63 !4 !8 !6 !5 !0 !7 i o q u y t !3 r !2 w !1 Component Parts Note Hard anodized Material Aluminum alloy No.
In this case, only step i is necessary. The installation position of the auto switch mounting band serves only as a rough guide, so check the operating condition of the auto switch and then readjust the band. i Install the auto switch on the switch holder, and secure it in place. Install the auto switch in the state of Fig. 1-6.