The CY1S-Z Rodless Cylinder - Magnetically Coupled uses industrial strength magnets located in the piston and external carriage to form a single unit that will travel when actuated with air pressure. It is a one piece unit integrated with slide bearings which provides lateral stability protecting it from side load impacts. The CY1S-Z cylinder tube has lube retainers on the internal and external
Series CY3B/CY3R Basic type / Direct mount type 6, 10, 15, 20, 25, 32, 40, 50, 63 CY3B CY3R CY3B CY1S CY1L CY1H CY1F CYP CY3R D-X Individual -X Technical data 1165 Direct mount type Basic type Magnetically Coupled Rodless Cylinder Series CY3B/CY3R Improved durability Improved bearing performance A 70% longer wear ring length achieving an improvement in bearing performance compared to the
Your search for CY1S returned 20 result(s)
There were no hits with the full part number, but there were 4 hits in the keyword search.
There were no hits with the full part number, but there were 1 hits in the keyword search.
Product Information » New Products Search Results
Magnetically Coupled Rodless Cylinder/Slider Type: Slide Bearing Series CY1S Replacement Procedure is 6, 10, 15, 20 25, 32, 40 P.317 Construction Slider type, slide bearing Actuators Modular F.R.L. Pressure Control Equipment Air Preparation Equipment Industrial Filters Replacement Procedure Actuators Modular F.R.L. Pressure Control Equipment Industrial Filters @8 @9 @6 @7 #1 #0 This figure
M4 x 0.7 10.5 16.5 28 6.5 12.5 CY1SG15-Z 7.5 9.5 5.4 16.6 12 2 38 6.5 5 6 52 40 28 29.5 20.5 15 39 20.5 M4 x 0.7 11 60 5.8 8 M5 x 0.8 10.5 16.5 28 5.5 11.5 CY1SG20-Z 10 9.5 5.4 21.6 16 2 44 8.5 5.5 8 62 46 36 37.5 24 19 45 20 M6 x 1 16 70 5.8 10 M6 x 1 10.5 22 28 5.5 17 CY1SG25-Z 10 11 6.5 26.4 16 2 52 8.5 5.5 8 70 54 40.5 40.5 27.5 21.5 53 21 M6 x 1 20 70 7 10 M6 x 1 12.5 22 49 7.5 17 CY1SG32
28 2.5 6 45 6.5 4.6 6 CY1SG15-Z 7.5 9.5 16.6 38 6.5 52 28 29.5 20.5 15 20.5 M4 x 0.7 M5 x 0.8 10.5 16.5 11.5 5.4 12 5 40 39 11 28 2 6 60 5.8 8 5.5 CY1F CY1SG20-Z 10 9.5 21.6 44 8.5 62 36 37.5 24 19 20 M6 x 1 M6 x 1 10.5 22 17 5.4 16 2 5.5 8 46 45 16 70 5.8 28 5.5 10 CY1SG25-Z M6 x 1 M6 x 1 10 11 26.4 52 8.5 70 40.5 40.5 27.5 21.5 21 12.5 22 17 6.5 16 2 5.5 8 54 53 20 70 49 7.5 7 10 CYP CY1SG32
Special function Electrical entry Indicator light Wiring (Output) In-line Perpendicular 0.5 (Nil) 3 (L) DC AC 5 (Z) MHT Type 3-wire (NPN) 3-wire (PNP) 24 V MHY M9NV M9N Solid state switch 5 V IC circuit 12 V M9PV M9P Standard MHW Relay, PLC Grommet Yes M9BV M9B 2-wire 12 V Water resistant (2-color indication) MRHQ F9BA Lead wire length symbols: 0.5 m Nil (Example) M9B 3 m L (Example) M9BL
This is a legacy product, and replaced byCDA2C50TN-600Z, CYL, TIE ROD, NON LUBE,AUTO-SW, ACTUATOR, CA1/CA2 TIE-ROD CYLINDER, NE, 50MM CA1 DBL-ACT AUTO-SW, 5.60841 lb
(Inlet air pressure: 0.7 MPa, Inlet air temperature: 20C) Accessory (Option)/Replacement Parts Applicable model ID20 ID30 ID40 ID60 6604113 6604113 660651 660651 ID-200S ID-300S ID-400S ID-600S ID-200Z ID-300Z ID-400Z ID-600Z ID-DPM8 Bracket Adsorbent set Note) Adsorbent set (for low dew point) Note) Indicator set Note) Adsorbent and adsorption tube filter for one air dryer (two adsorption
This is a legacy product, and replaced byCDG1DA40-600Z-C73L, CYL, AIR, DBL ACT, AUTO-SW, ACTUATOR, CG/CG3 ROUND BODY CYLINDER, ME, 40MM CG DBL-ACT AUTO-SW, 5.87899 lb
This is a legacy product, and replaced byMY1B25-600Z, CYL, RODLESS, MECH JOINT, ACTUATOR, MY1B GUIDED CYLINDER, IE, 25MM MY1B DBL-ACT AUTO-SW, 5.91941 lb
This is a legacy product, and replaced byCG1DN40-600Z, 40MM CG DOUBLE-ACTING, ACTUATOR, CG/CG3 ROUND BODY CYLINDER, MD, 40MM CG DOUBLE-ACTING, 5.51155 lb
This is a legacy product, and replaced byCDA2B40-600Z, CYLINDER, CA2, TIE ROD, TIE ROD CYLINDER, 3.13 lb
This is a legacy product, and replaced byCDG1BA40-600Z-XC6, BASE CYLINDER, ACTUATOR, CG/CG3 ROUND BODY CYLINDER, MC, 40MM CG OTHERS (COMBO), 4.9163 lb