The CY1S-Z Rodless Cylinder - Magnetically Coupled uses industrial strength magnets located in the piston and external carriage to form a single unit that will travel when actuated with air pressure. It is a one piece unit integrated with slide bearings which provides lateral stability protecting it from side load impacts. The CY1S-Z cylinder tube has lube retainers on the internal and external
How To Order: Magnetically Coupled Rodless Cylinder Slider Type: Slide Bearing ø 6, ø 10, ø 15, ø 20, ø 25, ø 32, ø 40 CY1S Series Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ Solid state auto switches marked with are produced upon receipt of order. There are other applicable auto switches other than listed above. For details, refer to page 1506. For details about auto switches with pre-wired connector, refer to pages 1648 and 1649.
A96 5V IC circuit Yes Grommet 24V A93 A90 100V Relay, PLC 5V,12V 2-wire No 100V or less IC circuit Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ Solid state auto switches marked are produced upon receipt of order.
1/28 Doc. no. CY*S-OM0078P PRODUCT NAME Magnetically Coupled Rodless Cylinder (Slider Type: Slide Bearing) MODEL / Series / Product Number Series CY1S-Z 2/28 Contents Safety Instructions P3P4 1. Mounting P5P7 1-1) Surface for mounting 1-2) Mounting the cylinder 1-3) Minimum necessary space for the installation of the cylinder 2. Operation P7P8 3. Functions P8P11 3-1) Piping selection 3-2)
Similar items in stock.
Your search for CY1S returned 20 result(s)
There were no hits with the full part number, but there were 4 hits in the keyword search.
There were no hits with the full part number, but there were 1 hits in the keyword search.
Product Information » New Products Search Results
Magnetically Coupled Rodless Cylinder/Slider Type: Slide Bearing Series CY1S Replacement Procedure is 6, 10, 15, 20 25, 32, 40 P.317 Construction Slider type, slide bearing Actuators Modular F.R.L. Pressure Control Equipment Air Preparation Equipment Industrial Filters Replacement Procedure Actuators Modular F.R.L. Pressure Control Equipment Industrial Filters @8 @9 @6 @7 #1 #0 This figure
Calculation example 7 Mounting on horizontal wall [1] Operating Conditions CY1SG25-600 Wa: Connection plate t = 10 (1.5 kg) Cylinder: CY1SG25-600 Cushion: Shock absorber Mounting: Horizontal wall mounting Speed: Va = 250 [mm/s] Wc: Rod L = 50 (0.5 kg) [2] Load Blocking Wd: Workpiece (2.5 kg) A = 33 50 Wb: Arm L = 105 (1.0 kg) 5 0 Z X Mass and center of gravity of the load 25 Center of gravity
MEmax is the allowable moment for V. 3 = ME/MEmax 3: Dynamic moment Calculation example z Mounting on horizontal wall [1] Operating Conditions CY1SG25-600 Wa: Connection plate t = 10 (1.5 kg) Cylinder: CY1SG25-600 Cushion: Shock absorber Mounting: Horizontal wall mounting Speed: Va = 250 [mm/s] Wc: Rod L = 50 (0.5 kg) Wd: Workpiece (2.5 kg) [2] Load Blocking Wb: Arm L = 105 (1.0 kg) A = 33
This is a legacy product, and replaced byCY1SG32-200BZ, CYL, RODLESS, SLIDER, SW CAP, ACTUATOR, CY1S GUIDED CYLINDER, LM, 32MM CY1S SLIDE BEARING, 11.24921 lb
Piping: G (Centralized Piping Type), Bore Size: 25mm, Port Thread: M Thread: Bore 6-15; Rc: Bore 20-40, Stroke: 200mm, Stopper Type: B [Shock Absorber/Adjustment Bolt (Metal Ended), Mounted on Both Sides]
Type: Rodless Cylinder, Cylinder Inner Diameter(Ø): 25, Stroke(mm): 200, Max. Load Mass (Horizontal Mounting)(kg): 20~39.9, Table Size Length L(mm): 70, Table Material: [Aluminum] Aluminum Alloy, Rodless Cylinder Joint Type: Magnetic, Guide: [Sliding Guide] Guide Type of Slide Bearing, Table Size Width W(mm): 99, Table Size Height H(mm): 54, Table Surface Treatment: No, Environment: General
Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) H7CN Since there are other applicable auto switches than listed, refer to page 460 for details. For details about auto switches with pre-wired connector, refer to the WEB catalog or the Best Pneumatics No. 2.
Piping: G (Centralized Piping Type), Bore Size: 25mm, Port Thread: M Thread: Bore 6-15; Rc: Bore 20-40, Stroke: 200mm, Stopper Type: B [Shock Absorber/Adjustment Bolt (Metal Ended), Mounted on Both Sides], Auto Switch: A93--Reed, DC Volt, AC Volt, LED, Horizontal