The CY1S-Z Rodless Cylinder - Magnetically Coupled uses industrial strength magnets located in the piston and external carriage to form a single unit that will travel when actuated with air pressure. It is a one piece unit integrated with slide bearings which provides lateral stability protecting it from side load impacts. The CY1S-Z cylinder tube has lube retainers on the internal and external
How To Order: Magnetically Coupled Rodless Cylinder Slider Type: Slide Bearing ø 6, ø 10, ø 15, ø 20, ø 25, ø 32, ø 40 CY1S Series Indicator light Load voltage Wiring (Output) Auto switch model Lead wire length (m) Electrical entry Pre-wired Type Special function connector Applicable load DC AC Perpendicular In-line 0.5 (Nil) 3 (L) 5 (Z) 1 (M) M9N M9P M9B M9NW M9PW M9BW M9NA1 M9PA1 M9BA1 M9NV M9PV M9BV M9NWV M9PWV M9BWV M9NAV1 M9PAV1 M9BAV1 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN
Auto switch model Lead wire length (m) Load voltage Wiring (output) Pre-wired connector Applicable load DC AC Indicator light Electrical entry Type Special function Perpendicular In-line 0.5 (Nil) 5 (Z) 3 (L) M9NV M9PV M9BV M9NWV M9PWV M9BWV 1 (M) M9N M9P M9B M9NW M9PW M9BW 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire IC circuit 5 V,12 V Reed switch Solid state switch
1/28 Doc. no. CY*S-OM0078P PRODUCT NAME Magnetically Coupled Rodless Cylinder (Slider Type: Slide Bearing) MODEL / Series / Product Number Series CY1S-Z 2/28 Contents Safety Instructions P3P4 1. Mounting P5P7 1-1) Surface for mounting 1-2) Mounting the cylinder 1-3) Minimum necessary space for the installation of the cylinder 2. Operation P7P8 3. Functions P8P11 3-1) Piping selection 3-2)
Similar items in stock.
Your search for CY1S returned 20 result(s)
There were no hits with the full part number, but there were 4 hits in the keyword search.
There were no hits with the full part number, but there were 1 hits in the keyword search.
Product Information » New Products Search Results
Magnetically Coupled Rodless Cylinder/Slider Type: Slide Bearing Series CY1S Replacement Procedure is 6, 10, 15, 20 25, 32, 40 P.317 Construction Slider type, slide bearing Actuators Modular F.R.L. Pressure Control Equipment Air Preparation Equipment Industrial Filters Replacement Procedure Actuators Modular F.R.L. Pressure Control Equipment Industrial Filters @8 @9 @6 @7 #1 #0 This figure
-700 Cushion: Shock absorber Mounting: Vertical mounting Speed: Va = 200 [mm/s] CY1SG20-700 Wa: Connection plate t = 10 (1.0 kg) Wb: Arm L = 100 (1.0 kg) Wc: Rod L = 50 (0.5 kg) Wd: Workpiece (3.0 kg) [2] Load Blocking Mass and center of gravity of the load Y Center of gravity Load no.
-700 Cushion: Shock absorber Mounting: Vertical mounting Speed: Va = 200 [mm/s] CY1SG20-700 Wa: Connection plate t = 10 (1.0 kg) Wb: Arm L = 100 (1.0 kg) Wc: Rod L = 50 (0.5 kg) Wd: Workpiece (3.0 kg) [2] Load Blocking Mass and center of gravity of the load Y Center of gravity Load no.
This is a legacy product, and replaced byCY1SG15-400Z-A93V, CYL, RODLESS, SLIDER, SW CAP, ACTUATOR, CY1S GUIDED CYLINDER, GM, 15MM CY1S SLIDE BEARING, 3.74785 lb
This is a legacy product, and replaced byCA2D40-400Z, CYL, TIE ROD, NON-LUBE, ACTUATOR, CA1/CA2 TIE-ROD CYLINDER, MD, 40MM CA1 DOUBLE-ACTING, 5.77860 lb
This is a legacy product, and replaced byCA2L50TN-400Z, CYL, TIE ROD, NON-LUBE, ACTUATOR, CA1/CA2 TIE-ROD CYLINDER, ND, 50MM CA1 DOUBLE-ACTING, 4.18878 lb
(Inlet air pressure: 0.7 MPa, Inlet air temperature: 20C) Accessory (Option)/Replacement Parts Applicable model ID20 ID30 ID40 ID60 6604113 6604113 660651 660651 ID-200S ID-300S ID-400S ID-600S ID-200Z ID-300Z ID-400Z ID-600Z ID-DPM8 Bracket Adsorbent set Note) Adsorbent set (for low dew point) Note) Indicator set Note) Adsorbent and adsorption tube filter for one air dryer (two adsorption
Purchase order number Number Name of articles ID20* ID30* ID40* ID60* ID-S0054 4 Filter element ID-S0055 ID-S0056 2 KA00066 5 Oring KA00072 KA00074 4 Table 2 Adsorbent set part Number Name of articles Purchase order number quantity ID20* ID30* ID40* ID60* ID-200S ID-300S ID-400S ID-600S 1011 Standard type 1 (Filter element, Adsorbent, Oring) Low dew point type ID*0*-**-Z ID-200Z ID-300Z ID-400Z