The CY1S-Z Rodless Cylinder - Magnetically Coupled uses industrial strength magnets located in the piston and external carriage to form a single unit that will travel when actuated with air pressure. It is a one piece unit integrated with slide bearings which provides lateral stability protecting it from side load impacts. The CY1S-Z cylinder tube has lube retainers on the internal and external
How To Order: Magnetically Coupled Rodless Cylinder Slider Type: Slide Bearing ø 6, ø 10, ø 15, ø 20, ø 25, ø 32, ø 40 CY1S Series Indicator light Load voltage Wiring (Output) Auto switch model Lead wire length (m) Electrical entry Pre-wired Type Special function connector Applicable load DC AC Perpendicular In-line 0.5 (Nil) 3 (L) 5 (Z) 1 (M) M9N M9P M9B M9NW M9PW M9BW M9NA1 M9PA1 M9BA1 M9NV M9PV M9BV M9NWV M9PWV M9BWV M9NAV1 M9PAV1 M9BAV1 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN
Load voltage Lead wire length (m) Auto switch model DC AC 0.5 (Nil) 3 (L) 5 (Z) 1 (M) Indicator light Electrical entry Wiring (output) Type Special function Pre-wired connector Applicable load M9N M9P M9B M9NW M9PW M9BW 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 5V,12V IC circuit Solid state switch Reed switch 12V Relay, PLC Yes Grommet Diagnostic indication (2-color
1/28 Doc. no. CY*S-OM0078P PRODUCT NAME Magnetically Coupled Rodless Cylinder (Slider Type: Slide Bearing) MODEL / Series / Product Number Series CY1S-Z 2/28 Contents Safety Instructions P3P4 1. Mounting P5P7 1-1) Surface for mounting 1-2) Mounting the cylinder 1-3) Minimum necessary space for the installation of the cylinder 2. Operation P7P8 3. Functions P8P11 3-1) Piping selection 3-2)
Similar items in stock.
Your search for CY1S returned 20 result(s)
There were no hits with the full part number, but there were 4 hits in the keyword search.
There were no hits with the full part number, but there were 1 hits in the keyword search.
Product Information » New Products Search Results
Magnetically Coupled Rodless Cylinder/Slider Type: Slide Bearing Series CY1S Replacement Procedure is 6, 10, 15, 20 25, 32, 40 P.317 Construction Slider type, slide bearing Actuators Modular F.R.L. Pressure Control Equipment Air Preparation Equipment Industrial Filters Replacement Procedure Actuators Modular F.R.L. Pressure Control Equipment Industrial Filters @8 @9 @6 @7 #1 #0 This figure
Piping: Bilateral Piping Type, Bore Size: 40mm, Port Thread: TN (NPT), Stroke: 900mm, Stopper Type: Bumper Bolt (Resin Tipped)
Piping: Bilateral Piping Type, Bore Size: 40mm, Port Thread: NPT, Stroke: 900mm, Stopper Type: Bumper Bolt (Resin Tipped), Auto Switch: -, Lead Wire or Prewired Connector: -, Number: -
This is a legacy product, and replaced byMY1B32TNG-900Z-A93L
This is a legacy product, and replaced byCDA2L50R-900Z, CYL, TIE ROD, NON LUBE, ACTUATOR, CA1/CA2 TIE-ROD CYLINDER, NE, 50MM CA1 DBL-ACT AUTO-SW, 7.89254 lb
Magnet: D (Built-in Magnet), Mounting: L (Axial Foot), Type: A (Air Cushion), Bore: 32mm, Port Thread Type: Rc (or M5, Depending on Style, Bore Size, and Thread Combination), Stroke: 900mm, Thread: Male Rod End, Suffix for Cylinder: w/o Rod Boot, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal
Magnet: D (Built-in), Series: A2 (Standard), Mounting: L (Axial Foot), Tube Material: Aluminum, Bore Size: 40mm, Port Thread: Rc, Stroke: 900mm, Rod Boot: None, Cushion: Air Cushion, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal
Bore: 40mm, Port Thread: TN (NPT), Piping: Standard, Stroke: 900mm, Stroke Adjustment Unit: Left: w/o Unit; Right: w/o Unit, Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal