The CY1F low profile Rodless Cylinder - Magnetically Coupled uses industrial strength magnets located in the piston and external carriage to form a single unit that will travel when actuated with air pressure. It is installed with a single axis internal linear guide to reduce its profile as much as 29% and up to 50% weight reduction compared to the CY1H Series.
- Bore sizes: 10,
Catalog: Basic type / Direct mount type Series CY3B/CY3R , 500 1000 1500 100, 150, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800 25 3000 32 40 3000 100, 150, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000 50 5000 63 Note 1) Long stroke specification (XB11) applies to the strokes exceeding 2000 mm.
Bore Size: 25mm, Port Thread: TN [NPT Thread (ø25)], Piping: L (Left Side Centralized Piping), Stroke: 450mm
Bore Size: 25mm, Port Thread: TN [NPT Thread (ø25)], Piping: Left Side Centralized Piping, Stroke: 450mm, Adjuster: -, Auto Switch: -, Lead Wire or Prewired Connector: -, Number: -
Bore Size: 25mm, Port Thread: TN [NPT Thread (ø25)], Piping: L (Left Side Centralized Piping), Stroke: 450mm, Adjuster: Both Sides Standard, Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: L (3m)
Bore Size: 25mm, Port Thread: TN [NPT Thread (ø25)], Piping: Left Side Centralized Piping, Stroke: 450mm, Adjuster: Both Sides Standard, Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: 3m, Number: -
Bore Size: 25mm, Port Thread: TN [NPT Thread (ø25)], Piping: L (Left Side Centralized Piping), Stroke: 150mm, Adjuster: A (Both Sides: 25mm Adjusting), Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: SAPC (0.5m Cord Length, M8-3 Pin Connector)
Bore Size: 25mm, Port Thread: TN [NPT Thread (ø25)], Piping: L (Left Side Centralized Piping), Stroke: 300mm, Adjuster: A (Both Sides: 25mm Adjusting), Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: SAPC (0.5m Cord Length, M8-3 Pin Connector)
Type: Rodless Cylinder, Cylinder Inner Diameter(Ø): 25, Stroke(mm): 300, Max. Load Mass (Horizontal Mounting)(kg): 10~19, Table Size Length L(mm): 70, Table Material: [Aluminum] Aluminum Alloy, Rodless Cylinder Joint Type: Magnetic, Guide: [Guideless] Prototype, Table Size Width W(mm): 128.5, Table Size Height H(mm): 46, Table Parallelism(µm): 50, Table Surface Treatment: [Anodize] Hard Anodize
Bore Size: 25mm, Port Thread: TN [NPT Thread (ø25)], Piping: Left Side Centralized Piping, Stroke: 150mm, Adjuster: Both Sides: 25mm Adjusting, Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: 0.5m Cord Length, M8-3 Pin Connector, Number: -
This is a legacy product, and replaced byCDG1BN25-350Z-M9PSAPC, 25MM CG DBL-ACT AUTO-SW, ACTUATOR, 25MM CG DBL-ACT AUTO-SW, 1.76369 lb
This is a legacy product, and replaced byCY1SG10-130BZ-M9PSAPC, CYL, RODLESS, SLIDER, SW CAP, ACTUATOR, CY1S GUIDED CYLINDER, EM, 10MM CY1S SLIDE BEARING, 2.30107 lb
This is a legacy product, and replaced byMGPL20TN-200AZ-M9PSAPC-XC9 MGP COMPACT GUIDE CYLINDER. CYL, GUIDE, B/BRG,ADJ STK/RETR. ACTUATOR. 20MM MGP. .00000 lb. HC.
This is a legacy product, and replaced byCDM2B25-200Z-M9PSAPC, CYL, RND BODY, DBL ACTING, ACTUATOR, CM2/CM3 ROUND BODY CYLINDER, IE, 25MM CM2 DBL-ACT AUTO-SW, 1.31143 lb
This is a legacy product, and replaced byCDG1BN20-125Z-M9PSAPC, 20MM CG DBL-ACT AUTO-SW, ACTUATOR, CG/CG3 ROUND BODY CYLINDER, HE, 20MM CG DBL-ACT AUTO-SW, 0.88309 lb
This is a legacy product, and replaced byCDG1BN20-50Z-M9PSAPC, CYL, AIR, DBL ACT, AUTO-SW, ACTUATOR, CG/CG3 ROUND BODY CYLINDER, HE, 20MM CG DBL-ACT AUTO-SW, .88184 lb
This is a legacy product, and replaced byMGPM20-20Z-M9PSAPC, CYL, COMPACT GUIDE, SLIDE *LQA, ACTUATOR, MGP COMPACT GUIDE CYLINDER, HM, 20MM MGP SLIDE BEARING, 3.94390 lb, Bore size (mm)ModelStandard stroke (mm) 1020253040507510012515017520025030035040020MGPM20?0.67?0.750.830.911.171.371.571.761.962.162.633.033.423.82
Bore Size: 25mm, Port Thread: TN [NPT Thread (ø25)], Piping: L (Left Side Centralized Piping), Stroke: 100mm, Adjuster: A (Both Sides: 25mm Adjusting)
Bore Size: 25mm, Port Thread: TN [NPT Thread (ø25)], Piping: L (Left Side Centralized Piping), Stroke: 200mm