Series CM2-Z double acting, double rod, stainless steel cylinders are compact, lightweight and offer high performance. The piston seal and rod seal design provides excellent life. Transparent auto switch bracket provides visibility of the status of the switch. Rubber bumpers are standard. The CM2-Z series offers a variety of mounting options.
wire 12V Connector IC circuit 3-wire (NPN) 2-wire 5V, 12V 12V Terminal conduit Relay, PLC Yes Yes No No No Yes Yes Yes 24V 3-wire (NPN) 3-wire (PNP) IC circuit 5V,12V 12V Diagnostic indication (2-color indication) Grommet 2-wire Water resistant (2-color indication) 4-wire (NPN) IC circuit 5V, 12V With diagnostic output (2-color indication) 3-wire (NPN equivalent) A96 IC circuit 5V A93
D-A93 45 to less than 50 stroke D-M9 D-M9W 15 to less than 20 stroke 45 to less than 55 stroke Note 2) D-A3A/A44A/G39A/K39A cannot be mounted on the centralized piping type Series CDM2P.
Your search for CM2 returned 30 result(s)
There were no hits with the full part number, but there were 22 hits in the keyword search.
There were no hits with the full part number, but there were 17 hits in the keyword search.
Product Information » New Products Search Results
Magnet: Built-in Magnet, Style: Pneumatic, Mounting: Axial Foot, Bore: 40mm, Port Thread: Rc, Stroke: 300mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None, Auto Switch: H7C--Solid State, Gen. Purpose, 2 Wire, Connector, Lead Wire or Prewired Connector: 3m, Number: -
Magnet: D (Built-in Magnet), Style: Pneumatic, Mounting: L (Axial Foot), Bore: 40mm, Port Thread: Rc, Stroke: 75mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None, Auto Switch: A93--Reed, DC Volt, AC Volt, LED, Horizontal
Magnet: Built-in Magnet, Style: Pneumatic, Mounting: Axial Foot, Bore: 40mm, Port Thread: Rc, Stroke: 75mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None, Auto Switch: A93--Reed, DC Volt, AC Volt, LED, Horizontal, Lead Wire or Prewired Connector: -, Number: -
This is a legacy product, and replaced byCA2T63-300Z CA1/CA2 TIE-ROD CYLINDER. CYL, TIE ROD, NON-LUBE. ACTUATOR. 63MM CA1 DOUBLE-ACTING. 10.60147 lb. PD.
This is a legacy product, and replaced byCY1SG15-300Z, CYL, RODLESS, SLIDER, ACTUATOR, CY1S GUIDED CYLINDER, GM, 15MM CY1S SLIDE BEARING, 2.51040 lb, Bore size (mm)ModelAllowable load mass (Wv)(kg)Maximum operating pressure (Pv) (MPa)15CY1S15H7.00.65
This is a legacy product, and replaced byCDM2C32-300Z, CYL, RND BODY, DBL ACTING, ACTUATOR, CM2/CM3 ROUND BODY CYLINDER, LE, 32MM CM2 DBL-ACT AUTO-SW, 2.10596 lb
This is a legacy product, and replaced byCDG1RA63-300Z-C73L, CYL, AIR, BLOCK MT. AUTO-SW, ACTUATOR, CG/CG3 ROUND BODY CYLINDER, PE, 63MM CG DBL-ACT AUTO-SW, 7.57444 lb
(Inlet air pressure: 0.7 MPa, Inlet air temperature: 20C) Accessory (Option)/Replacement Parts Applicable model ID20 ID30 ID40 ID60 6604113 6604113 660651 660651 ID-200S ID-300S ID-400S ID-600S ID-200Z ID-300Z ID-400Z ID-600Z ID-DPM8 Bracket Adsorbent set Note) Adsorbent set (for low dew point) Note) Indicator set Note) Adsorbent and adsorption tube filter for one air dryer (two adsorption
This is a legacy product, and replaced byMBD63TN-300Z, CYL, TIE ROD, ACTUATOR, MB TIE-ROD CYLINDER, PD, 63MM MB DOUBLE-ACTING, 12.34588 lb